12
-EN
01GB05CDA105E.fm
ALPINE CDA-105E 68-09359Z81-A (EN)
Adjusting Subwoofer Level/Bass Level/
Treble Level/Balance (Between Left and
Right)/Fader (Between Front and Rear)/
Defeat
1
Press
Rotary encoder (AUDIO)
repeatedly to
choose the desired mode.
Each press changes the mode as follows:
SUBW LEVEL
*
BASS LEVEL
TREBLE
LEVEL
BALANCE
FADER
DEFEAT
VOLUME
SUBW LEVEL
Subwoofer level: +0 ~ +15
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: L15 ~ R15
Fader: R15 ~ F15
Defeat: ON/OFF
Volume: 0 ~ 35
•
If no operation is performed for 5 seconds after selecting the SUBW
LEVEL, BASS LEVEL, TREBLE LEVEL, BALANCE, FADER or
DEFEAT mode, the unit automatically returns to normal mode.
* When the subwoofer mode is set to OFF, its level cannot be adjusted.
Refer to “Turning Subwoofer ON/OFF” (page 14).
2
Turn the
Rotary encoder
until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted settings of
BASS and TREBLE will return to the factory defaults.
•
Depending on the connected devices, some functions and display
indications do not work.
Setting the Subwoofer Level
You can change the Subwoofer Level to create your own tonal
preference.
1
Press
SOUND SETUP
to activate the Sound Setting
mode.
2
Turn the
Rotary encoder
to select the SUBW
LEVEL Adjustment mode, and then press
/
ENT
.
SUBW LEVEL
*
1
BASS
*
2
TREBLE
*
2
HPF
*
2
SUBW LEVEL
3
Turn the
Rotary encoder
to select the desired
subwoofer level (+0~+15).
•
If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
•
When subwoofer is set to OFF and DEFEAT is set to ON, pressing
the SOUND SETUP button momentarily will not be functional.
*
1
When the subwoofer mode is set to OFF, its level cannot be adjusted,
refer to “Turning Subwoofer ON/OFF” (page 14).
The adjustment can also be made by pressing
Rotary encoder
(AUDIO)
. Refer to “Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Defeat” (page 12).
*
2
The function is inoperable when DEFEAT is set to ON.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
1
Press
SOUND SETUP
to activate the Sound Setting
mode.
2
Turn the
Rotary encoder
to select the BASS
Adjustment mode, and then press
/
ENT
.
SUBW LEVEL
*
3
BASS
*
4
TREBLE
*
4
HPF
*
4
SUBW LEVEL
3
-1 Press
BAND
to select the desired bass centre
frequency.
80 Hz
100 Hz
200 Hz
60 Hz
80 Hz
Emphasizes the displayed bass frequency ranges.
3
-2 Press
SOURCE/
to select the desired bass
bandwidth.
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.
Sound Setting
/ENT
BAND
Rotary encoder (AUDIO/LOUD)
SOURCE/
SOUND SETUP
/ESC
Setting the Bass Centre Frequency
Setting the Bass Bandwidth
1
2
3
4
01GB00CDA105E.book Page 12 Thursday, November 6, 2008 2:22 PM
