manualshive.com logo in svg

Alpha Radio 87A, Operating Manual

Share
Download
Alpha Radio 87A Operating Manual Download Page 28

 

Page 28 

 

 

 

Installing the

 AlphaRemote 

Software

 

 

1.  Close any programs running under Windows. 

2.  Insert AlphaRemote CD into CD drive (or disk #1 in 

floppy drive). 

3.  Click START on taskbar, then RUN. 

4. Click BROWSE and select My Computer, 

X:\setup.exe, then click OPEN.  When X:\setup.exe 
is showing in RUN window, click OK to start 
installation of AlphaRemote.  Follow the instructions 
on screen.  (Note:  X is the drive letter for your CD or 
floppy drive). 

5.  To run the AlphaRemote program click START on 

taskbar, then PROGRAMS, then select the Program 
Group where software was installed (default is 
AlphaRemote).  Click the AlphaRemote icon once to 
start program.  (NOTE:  The Alpha 87A must be 
connected to the AC power BEFORE starting the 
software.) 

6.  Click once on CONTROL, then CONFIGURE, then 

ADD AMPLIFIER.  Select the desired serial port.  
The default SETTINGS for communications 
parameters will be correct if a standard 25-pin (87A) 
to 9-pin (computer) modem cable is used (see 
paragraph 9 below).  Click OK to save the selected 
parameters. 

7.  If you have more than one 87A then select another 

amplifier to configure or click OK to close the 
CONFIGURE window if you are only setting up one 
87A.  The AlphaRemote window will open showing 
status and operating parameters of the selected 87A 
amplifier(s). 

 

8.  The front panel controls of the amplifier are 

duplicated in the AlphaRemote window.  Both Local 
and Remote control of the 87A are possible when 
the program is running. 

9.  A standard 25-pin to 9-pin modem cable will provide 

the correct connections between the Alpha 87A and 
computer serial port for 4800 baud data.  If a 25-pin 
to 25-pin cable is used between the 87A and 
computer, refer to attached sheet (or page 19 of the 
87A Operating Manual) for pins that must be 
disconnected at one end of the cable. 

10. 

If AlphaRemote software is to be used with an 87A 
which also has a DAS connected, the cable between 
the DAS and computer must have pins 
disconnected on the DAS end (see attached sheet).  
This is necessary whether using a 25-pin to 9-pin 
cable OR a 25-pin to 25-pin cable between the DAS 
and computer.

 

 

Alpha 87A User Manual Rev 2.0 

Summary of Contents for 87A























































Reviews:

No comments

Brands by name

Popular brands

Load more brands