Alpha Radio 87A Operating Manual Download Page 1

 

A L P H A   R A D I O   P R O D U C T S  

ALPHA 87A

 

O

perating 

M

anual

DISCLAIMER 

 

Information in this document is subject to change without 
notice.  Information provided by Alpha Radio Products Inc.® 
is believed to be correct and reliable.  However, no 
responsibility is assumed by Alpha Radio Products, LLC., 
unless otherwise expressly taken.  Companies, names, and 
data used as examples are fictitious, unless otherwise noted.   

No part of this document may be reproduced or transmitted 
in any form or by any means, graphic, electronic, or 
mechanical, for any purpose without the express permission 
of Alpha Radio Products, Inc.  Alpha Radio Products, Inc. 
may have patents or pending patents, trademarks, 
copyrights, or other property rights covering the subject 
matter in this document.  The furnishings of this document 
does not give you license to these patents, trademarks, 
copyrights, or other intellectual property, except as expressly 
written in any license agreement form 

 

 

Alpha Radio Products  
6185 Arapahoe Road • Boulder, CO 80303 
Phone 303.473.9232 • Fax 303.473.9660 
 
Read this entire manual and all other publications pertaining 
to the work to be performed before you install, operate, or 
maintain this equipment.  Practice all product safety 
instructions and precautions.  Alpha Radio Products, LLC. 
provides information on its products and associated hazards, 
but it assumes no responsibility for the after-sale operation of 
the equipment or the safety practices of the Owner or User.  
See Warranty and Notices Appendix. 

©Copyright 2005 by Alpha Radio Products, LLC. 

All rights reserved

.

Page i 

Alpha 87A User Manual Rev 2.0 

Summary of Contents for 87A























































Reviews: