background image

6

Contact with a “live” wire will make exposed metal parts of the tool “live” and 

shock the operator.

3.   Always wear safety glasses with side shields.

  Everyday eye-glasses have 

only impact resistant lenses; they are NOT safety glasses.

4.   

Protect your lungs.

  Wear a face or dust mask if the operation is dusty. 

5.   

Protect your hearing.

  Wear hearing protection during extended periods of 

operation.

6.   Inspect tool cords periodically and if damaged, have repaired at your 

nearest Factory Service Center or other Authorized Service Organization.

 

Constantly stay aware of cord location.

7.   Check damaged parts.

  Before further use of the tool, a guard or other part 

that is damaged should be carefully checked to determine that it will operate 

properly and perform its intended function.  

8.  Check for alignment of moving parts, binding of moving parts, breakage 

of parts, mounting, and any other conditions that may affect its operation.

  

A  guard or other part that is damaged should be properly repaired or replaced 

by an authorized service center.

9.  Do not abuse cord.

  Never carry the tool by the cord or yank it to disconnect 

it  from  the  receptacle.    Keep  cord  away  from  heat,  oil,  and  sharp  edges.  

Following this rule will reduce the risk of electric shock or fire.

10.  Make sure your extension cord is in good condition.

    When  using  an 

extension cord, be sure to use one heavy enough to carry the current your 

product will draw. An undersized cord will cause a drop in line voltage resulting 

in loss of power and overheating.

11.  Inspect for and remove all foreign objects from workpiece before 

polishing.

 Follow this rule will reduce the risk of serious personal injury.

12. 

Drugs, alcohol, medication, Do not operate tool while under the influence 

of drugs, alcohol, or any medication. 

 Follow this rule will reduce the risk of 

electric shock, fire, or serious personal injury.

13.   Keep hands away from polishing area.

 Follow this rule will reduce the risk 

of cuts, scrapes, or serious personal injury.

14.   Save these instruction.

 Refer to them frequently and use them to instruct 

others who may use this tool.  If you loan someone this tool, loan them these 

instructions.

Summary of Contents for VDP-700

























Reviews: