background image

 

 

AL-WPC8 - 

programmable control panel

 

 

Preface 

Read this user manual carefully before using the product. Pictures are shown in this 
manual for reference only. Different models and specifications are subject to real 
product. 

This manual is only for operation instruction, please contact the local distributor for 
maintenance assistance. The functions described in this version were updated till April, 
2018. In the constant effort to improve the product, we reserve the right to make 
functions or parameters changes without notice or obligation. Please refer to the 
dealers for the latest details. 

 

FCC Statement 

This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. It has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference in a commercial 
installation. 

Operation of this equipment in a residential area is likely to cause interference, in which 
case the user at their own expense will be required to take whatever measures may be 
necessary to correct the interference 

Any changes or modifications not expressly approved by the manufacture would void 
the user’s authority to operate the equipment. 

         

           

     

 
Trademarks 

Product model and logo are trademarks. Any other trademarks mentioned in this 

manual are acknowledged as the properties of the trademark owner. No part of this 

publication may be copied or reproduced without the prior written consent. 

 

 

Summary of Contents for AL-WPC8

































Reviews: