background image

Series SLTP, SETP, SNTP, SLTBP, SETBP, SNTBP

ALLWEILER

a

12

7.2.2.3 Mounting the rotor and rotor-side joint

– With  a  brass  drift,  drive  bushes  for  coupling  rod  pin

(303) half-way into rotor (401).

– Press coupling rod bush (302) into the coupling rod

(307)  so  that  the  longitudinal  axis  of  the  oval  hole
(marked  by  2  notches)  coincides  with  the  longitudi-
nal  axis  of  the  coupling  rod  and  the  coupling  rod
bush protrudes symmetrically from both sides of the
coupling rod (please refer to Figure 6 below.

Figure 6: Pressing- in of the coupling rod bush

– Push clamping bands (306), cover sleeves (308) and

retaining sleeve (304) onto the shank of the coupling
rod (307).

– Push  coupling  rod  (307)  into  the  head  of  the 

rotor (401).

– Push  coupling  rod  pin  (301)  into  the  coupling  rod

bush (302), and drive in bushes for coupling rod pin
(303) completely.

– Polish retaining sleeve (304) at the outside diameter,

if  necessary,  with  emery,  and  mount  on  the  head  of
the rotor(401).

– Following  mounting  of  the  retaining  sleeve  (304),

secure same against axial displacement on the head
of the rotor (401).

B

For  these  purposes,  drive  face  of 
the  retaining  sleeve  (304)  into  the

groove at the head of the rotor (401) with one punch
mark (please refer to Figure 7 below).

Figure 7: Locking the retaining sleeve.

– Mount  cover  sleeve  (308)  with  screw  driver,  lift  top

with screw driver, run spray pipe of the oil can under
the sleeve and fill the space in the joint with Allweiler
Spezialgelenköl Type B or Öl ET 15 10 ISO 460 of Tri-
bol Lubricants GmbH, Mönchengladbach, Germany. If
used  for  foodstuffs,  with  Allweiler  Spezialgelenköl
Type BL or Öl 1810 / 460 of Tribol Lubricants GmbH,
Möchengladbach,  Germany.  Lubricant  quantity  see
table, Section 7.1.2.6 above.

– Check whether bent loop of the clamping band (306)

rests against the clamping band buckle. If not, press
against  by  means  of  commercial  flat  pliers  (please
refer to Figure 8 below).

Figure  8:  Press  clamping  band  loop  against  clamping
band buckle.

– Place  clamping  bands  (306)  in  the  surrounding

grooves of the cover sleeve (308), and clamp.

Note: 

For  these  purposes,  the  following  clamping

tool must be used:

For pump sizes 

SLTP  720.1,  SETP  380.1,  SETP  380.2,  SETP  550.1
SNTP 200.1, SNTP 200.2, SNTBP 380.1, SETBP 380. 2,
SETBP  550.1,  SNTBP  200.1,  SNTBP  200.2  the  clam-
ping tool bearing the designation PoK-It II.

For pump sizes 

SLTP  1560.1,  SETP  750.1,  SETP  750.2,  SETP  1000.1,
SNTP  380.1,  SNTP  380.2  the  clamping  tool  bearing
the designation Band-It together with adapter J050.

The said tools may be obtained from us.
When clamping the clamping bands, proceed as fol-
lows:

x

Clamping  with  clamping  tool  Band-It  and  adapter
J050.

– Introduce  band  end  of  the  clamping  band  (306)

against the clamping band buckle into the clamping
tool with adapter.

– Hold clamp end with the eccentric lever of the clam-

ping tool, and clamp clamping band (306) by turning
the crank (Figure 9).

Figure  9:  Clamping  the  clamping  band  by  means  of
clamping tool Band-It and adapter J050.

Summary of Contents for SETBP Series





















Reviews: