Allsteel Harvest Rustic Seated Height Table Installation Instructions Manual Download Page 9

Page: 9 / 10

Page 9 of 10

3430399500

Harvest Rustic Table: Non-Powered

Installation Packet

x16

1. Install leveling glides into threaded insert on each leg.

2. Attach foot rest to legs with (8) 1/4-20 x 3/4” machine screws. Repeat for opposite end.

3. Insert (1) Double-Hole Dowel Nut into each side of foot rail. Rotate nut so the threaded hole

and slot are facing end of the rail.

4. Place foot rail between foot rests and install (2) 5/16 x 2” machine screws into the threaded

dowel holes of each end. Repeat for remaining foot rail.

Glide

Foot Rest & Foot Rail (standing height only)

Hardware:

Foot Rest

3/4” Machine Screws

2” Machine

Screws

Dowel

Nut

Build view

Stand view

1. Once fully assembled, lift and rotate the table to the upright position.

2. Check legs to make sure that they are perpendicular to the floor.

3. Level table.

Flip Table Upright

*Important*

Table should be rolled by at least two installers. Table should be lifted while flipping due

to the overall weight. Failure to adequately support table may result in damage to legs.

Summary of Contents for Harvest Rustic Seated Height Table










