AllSportSystems MICROBAY 10W Setup Manual Download Page 13 | Manualshive

Page: 13 / 24

background image

All

SportSystems, Inc.

©

2021

Step 6 - Before hanging the screen

Creases:

Screen may have creases from being folded during shipment. These creases will lighten

over time. If you wish, you may steam or iron the screen prior to hanging.

Cleaning:

Over time your screen may become stained or marked from ball impacts. Your screen

can be placed in the washing machine. Be sure to use

MILD

detergent on a gentle cycle.

DO NOT USE BLEACH OR PLACE SCREEN IN DRYER

IDENTIFY THE FRONT SIDE of your screen:

The AllSportSystems Logo and smooth face of the grommets will always be on the front side.
Additionally, velcro is sewn along the right and left edge of the screen front. Blackout side
panels attach to this velcro (see Blackout installation section).

Page 13 of 24

Table of Contents

Last Revised 8/25/2021

«
...
11
12
13
14
15
...
»

Summary of Contents for MICROBAY 10W

























Reviews:

No comments

Related manuals for MICROBAY 10W

Brand: CAME Pages: 2

Brand: N-Com Pages: 28

AWPH360N - PAN/TILT HEAD

Brand: Panasonic Pages: 48

Brand: Dakota Digital Pages: 2

Brand: Dakota Digital Pages: 6

Brand: Dakota Digital Pages: 7

Brand: Dakota Alert Pages: 2

Brand: A&D Pages: 35

Brand: Oki Pages: 3

Brand: Manfrotto Pages: 2

Brand: ICON Pages: 8

Brand: Sanitas Pages: 52

smartsensor advance

Brand: Wavetronix Pages: 2

Brand: X-lite Pages: 5

Brand: Xerox Pages: 13

Brand: Xerox Pages: 41

WaterGuard CM2300

Brand: Mobeye Pages: 32

Brand: PROAIM Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands