ALLNIC AUDIO T-2000 Owner'S Manual Download Page 6

 

 

As are all Allnic Audio products, the T-2000 

30th Anniversary

 is fully RoHS (EU Reduction of Hazardous 

Substances regulation) compliant in construction and materials. 

 

WHAT’S IN THE BOX? 

 

Please check that the shipping box contains the following: 

 

 

One (1) Allnic T-2000 

30th Anniversary

 stereo integrated amplifier 

 

One (1) Allnic remote control 

 

One (1) Allen wrench for screws on top of the tube chimneys 

 

One (1) 15 Amp IEC type power cord 

 

One (1) Owner’s Manual 

 

Note:   

1)

 

The T-2000 

30th Anniversar

y ships with the tubes installed.  

2)

 

The T-2000 

30th Anniversary

 will work with most IEC type aftermarket power cords. The 

Allnic 

ZL-3000 and ZL-5000 power cables

 will make an excellent match. Of course, only you can 

determine the power cord that works most synergistically with the T-2000 

30th Anniversary

 in 

your system. 

3)

 

Be sure the T-2000 30

th

 Anniversary is set for the AC voltage of your location. If it is not, DO 

NOT connect it to your AC outlet. Please contact your Allnic dealer. 

 

We advise that you keep the boxes and other packing materials that your T-2000 

30th Anniversary

 

came in. It will be useful if you sell your T-2000 

30th Anniversary

 or in the unlikely event you need to 

ship it for service. 

 

SAFETY 

 

 

Remove ALL protective cushioning material (cardboard around tubes) inside the tube 

chimneys before operation. The tube chimneys should contain NOTHING except the tubes. 

 

Disconnect the power cord by pulling the plug, not the cable. 

 

Do not attempt any repairs. Do not remove the unit’s chassis cover without specific 

authorization from your Allnic Audio dealer. 

 

Keep the power cord away from heat sources. 

 

Keep the unit away from liquids – do not allow any liquid to enter the interior of the unit. 

 

When the unit is moved from a cold to a warm environment, allow sufficient time for any 

condensation to evaporate before plugging the T-2000 

30th Anniversary

 into an AC connection. 

 

Do not attempt any repairs. 

 

See the notes on “Location, Location, Location”. 

 

 

 

 

 

Summary of Contents for T-2000


















Reviews: