background image

508134-01

Issue 2045

Page 39 of 56

Condensate Piping

This  unit  is  designed  for  either  right-  or  left-side  exit  of 

condensate piping. Refer to Figure 41 for condensate trap 

locations.

NOTE: 

If necessary the condensate trap may be installed 

up to 5’ away from the furnace. Use PVC pipe to connect 

trap to furnace condensate outlet. Piping from furnace 

must slope down a minimum of 1/4” per ft. toward trap.

1. 

Determine which side condensate piping will exit the 

unit, location of trap, field-provided fittings and length 

of PVC pipe required to reach available drain.

2. 

For  furnaces  with  a  1/2”  drain  connection  use  a  3/8 

allen  wrench  and  remove  plug  (Figure  41)  from  the 

cold end header box at the appropriate location on the 

side  of  the  unit.  Install  field-provided  1/2  NPT  male 

fitting  into  cold  end  header  box.  For  furnaces  with 

a  3/4”  drain  connection  use  a  large  flat  head  screw 

driver  or  a  1/2”  drive  socket  extension  and  remove 

plug. Install provided 3/4 NPT street elbow fitting into 

cold end header box. Use Teflon tape or appropriate 

pipe dope.

3. 

Install the cap over the clean out opening at the base 

of the trap. Secure with clamp. See Figure 47 or Figure 

48.

4. 

Install drain trap using appropriate PVC fittings, glue 

all  joints.  Glue  the  provided  drain  trap  as  shown  in 

Figure 47 or Figure 48. Route the condensate line to 

an open drain. Condensate line must maintain a 1/4” 

downward slope from the furnace to the drain.

5. 

Figure  45  shows  the  furnace  and  evaporator  coil 

using a separate drain. If necessary the condensate 

line  from  the  furnace  and  evaporator  coil  can  drain 

together. See Figure 46. The field provided vent must 

be a minimum 1” to a maximum 2” length above the 

condensate drain outlet connection.

NOTE: 

Appropriately  sized  tubing  and  barbed  fitting 

may be used for condensate drain. Attach to the drain 

on the trap using a hose clamp. See Figure 42.

6. 

If unit will be started immediately upon completion of 

installation, prime trap per procedure outlined in Unit 

Start-Up section.

Condensate line must slope downward away from the 

trap to drain. If drain level is above condensate trap, 

condensate  pump  must  be  used.  Condensate  drain 

line should be routed within the conditioned space to 

avoid  freezing  of  condensate  and  blockage  of  drain 

line. If this is not possible, a heat cable kit may be used 

on the condensate trap and line. Heating cable kit is 

available from Allied in various lengths; 6 ft. (1.8m) - kit 

no. 26K68 and 24 ft. (7.3m) - kit no. 26K69.

Figure 41. Condensate Trap and Plug Locations

Trap

(same on

right side)

Plug

(same on left

side)

1-1/2 in.

Tubing

Hose Clamp

Barbed Fitting

Elbow

Figure 42. 

Field-Provided Drain Components

Do not use copper tubing or existing copper condensate 

lines for drain line.

 CAUTION

Summary of Contents for 92G1DFE

























































Reviews: