background image

507651-01

Issue 1907

Page 13  of  32

Venting Using a Masonry Chimney

The following additional requirements apply when a lined 

masonry chimney is used to vent this furnace.

• 

Masonry  chimneys  used  to  vent  Category  I  central 

furnaces must be either tile lined or lined with a listed 

metal  lining  system  or  dedicated  gas  vent.  Unlined 

masonry chimneys are prohibited. See Figure 15 and 

Figure 17 for common venting.

• 

A  chimney  with  one  or  more  sides  exposed  to  the 

outside of the structure is considered to be an exterior 

chimney.

• 

An exterior masonry chimney that is not tile lined must 

be lined with B1 vent or a listed insulated flexible metal 

vent. An exterior tile lined chimney that is sealed and 

capped may be lined with a listed uninsulated flexible 

metal vent.

• 

If  the  existing  chimney  will  not  accommodate  a 

listed metal liner, either the chimney must be rebuilt 

to  accommodate  one  of  these  liners  or  an  alternate 

approved venting method must be found.

• 

Insulation  for  the  flexible  vent  pipe  must  be  an 

encapsulated fiberglass sleeve recommended by the 

flexible vent pipe manufacturer. 

Refer to the tables and the venting information contained 

in these instructions to properly size and install the venting 

system.

Once  the  venting  system  is  installed,  attach  the 

“Disconnected  Vent”  warning  sticker  to  a  visible  area 

of the plenum near the vent pipe. See Figure 16. The 

warning sticker is provided in the bag assembly. Order 

kit 66W04 for additional stickers.

   IMPORTANT

Figure 15. 

Common Venting Using Metal-Lined

Masonry Chimney

NOTE:

 Refer to the provided venting tables for installations. 

Refer to the capacity requirements shown in the provided 

venting tables.

Asphyxiation hazard. The exhaust vent for this furnace 

must be securely connected to the furnace flue transition 

at all times.

   WARNING

DO NOT

  insulate  the  space  between  the  liner  and  the 

chimney wall with puffed mica or any other loose granular 

insulating material.

SINGLE appliance venting of a fan assisted furnace into 

a tile lined masonry chimney (interior or outside wall) is 

prohibited. The chimney must first be lined with either 

type  B1  vent  or  an  insulated  single  wall  flexible  vent 

lining  system  which  has  been  sized  according  to  the 

provided venting tables and the vent pipe manufacturer’s 

instructions.

   IMPORTANT

FLUE TRANSITION

COLLAR

VENT PIPE

(min. 6” length)

“DISCONNECTED VENT”

WARNING

STICKER

FLUE 

TRANSITION

COLLAR

VENT PIPE

(min. 6” length)

“DISCONNECTED VENT”

WARNING

STICKER

Figure 16. 

Vent Connection Upflow and Horizontal Position

Summary of Contents for 80G1UHEX Series

































Reviews: