507043-03
Page 9 of 9
Issue 1337
Homeowner’s Information
Important System Information
• Your system should never be operated without a
clean air filter properly installed.
• Return air and supply air registers should be free
from restrictions or obstructions to allow full flow of
air.
Regular Maintenance Requirements
Your system should be regularly inspected by a
qualifed service technician. These regular visits may
include (among other things) checks for:
• Motor operation
• Ductwork air leaks
• Coil & drainpan cleanliness (indoor and outdoor)
• Electrical component operation & wiring check
• Proper refrigerant level & refrigerant leaks
• Proper airflow
• Drainage of condensate
• Air filters(s) performance
• Blower wheel alignment, balance & cleaning
• Primary & secondary drain line cleanliness
• Proper defrost operation (heat pumps)
There is some routine maintenance procedures you
can do to help keep your system operating at peak
performance between visits.
Air Filter
Inspect air filters at least monthly and replace or clean
as required. Disposable filters should be replaced.
Washable filters may be cleaned by soaking in mild
detergent and rinsing with cold water. Replace filters with
the arrows pointing in the direction of airflow. Dirty filters
are the most common cause of poor heating/cooling
performance and compressor failures.
Indoor Coil
If the sytem has been operated with a clean filter in
place, it should require minimal cleaning. Use a vacuum
cleaner and soft brush attachment to remove any
accumulation of dust from the top and underside of the
finned coil surface. However, perform this maintenance
only when the coil is completely dry.
If the coil cannot be cleaned by this method, call your
dealer for service. It may need a detergent solution and
rinsing with water for cleaning, which may require coil
removal, You should not attempt this yourself.
Condensate Drain
During cooling season check at least monthly for free
flow of drainage and clean if necessary.
Condenser Coils
Grass cuttings, leaves, dirt, dust, lint from clothes dry-
ers, and fall off trees can be drawn into coils by
movement of the air. Clogged condenser coils will lower
the efficiency of your unit and cause damage to the
condenser.
Periodically, debris should be brushed from the
condenser coils.
SHARP OBJECT HAZARD!
WARNING
Condenser coils have sharp edges. Wear adequate
body protection on body extremities (e.g. gloves) .
FAILURE TO FOLLOW THIS WARNING COULD
RESULT IN BODILY INJURY.
Use a soft brush with light pressure only. DO NOT
damage or bend condenser coil fins. Damaged or bent
fins may affect unit operation.
Painted Surfaces
For maximum protection of the unit’s finish, a good
grade of automobile wax should be applied every year. In
geographical areas where water has a high concentration
of minerals (calcium, iron, sulfur, etc.) , it is recommended
that lawn sprinklers not be allowed to spray the unit. In
such applications, the sprinklers should be directed away
from the unit. Failure to follow this precaution may result
in premature deterioration of the unit finish and metal
components.
In sea coast areas, special maintenance is required
due to the corrosive atmosphere provided by the high salt
concentration in ocean mists and the air. Periodic
washing of all exposed surfaces and coil will add
additional life to your unit. Please consult your installing
dealer for proper procedures in your geographic area.
IF YOUR SYSTEM DOES NOT WORK,
BEFORE REQUESTING A SERVICE CALL:
1. Ensure thermostat is set below (cooling) or above
(heating) room temperature and that the system lever
is in the “COOL”, “HEAT” or “AUTO” position.
2. Inspect your return air filter: If it is dirty your air condi
-
tioner may not fuction properly.
3. Check indoor and outdoor disconnect switches.
Confirm circuit breakers are ON or that fuses have not
blown. Reset breakers/replace fuses as necessary.
4. Inspect the outdoor unit for clogged condenser
coils,(grass cuttings, leaves, dirt, dust or lint). Ensure
that branches, twigs or other debris are not obstructing
the condenser fan.
IF YOUR SYSTEM STILL DOES NOT OPERATE, CON-
TACT YOUR SERVICING DEALER.
Be sure to describe the problem, and have the model
and serial numbers of the equipment available.
If warranted replacement parts are required, the war-
ranty must be processed through a qualified distribution
location.