manualshive.com logo in svg

Allied 295, Operator And Parts Manual, Page: 3 / 36

Share
Download
Allied 295 Operator And Parts Manual Download Page 3

3

Table of Contents - 295 Loader

Table of Contents

Introduction .................................................................................................................................4

•  Terminology .....................................................................................................................4
•  Hydraulic (Hose Kit) .........................................................................................................5

Specifications ...............................................................................................................................6

Safety ............................................................................................................................................8

•  Safety ................................................................................................................................8
•  General Safety ..................................................................................................................9
•  Installation ........................................................................................................................9
•  Safety Decals ..................................................................................................................10
•  Important Precautions ................................................................................................... 11

Operation ...................................................................................................................................12

•  Operation ........................................................................................................................12
•  Operating Suggestions for Loading .............................................................................13
•  Operating Suggestions for Backfilling .........................................................................14
•  Attaching the Loader to Your Tractor .............................................................................15
•  Removing the Loader from Your Tractor .......................................................................17

General Instructions ..................................................................................................................19

Troubleshooting .........................................................................................................................20

 

Maintenance ..............................................................................................................................22
Lubrication .................................................................................................................................22

Bolt Torque .................................................................................................................................23

•  Checking Bolt Torque .....................................................................................................23

Parts ............................................................................................................................................24

•  Sub Frame Assembly and Parts List .............................................................................24
•  Main Frame Assembly and Parts List ...........................................................................26
•  Hydraulic Plumbing Assembly and Parts List ..............................................................28

Assembly ....................................................................................................................................30

•  Hydraulic Cylinder Assembly ........................................................................................30

Pre-delivery Check List ..............................................................................................................31

Warranty .....................................................................................................................................32

 

Manufacturer’s statement: for technical reasons Buhler Industries Inc. reserves the right to modify 
machinery design and specifications provided herein without any preliminary notice.
 Information provided herein is of descriptive nature. Performance quality may depend on soil fertility,  
applied agricultural techniques, weather conditions and other factors.

Summary of Contents for 295





































Reviews:

No comments