manualshive.com logo in svg

Allied Vision Technologies Prosilica GS Series, Technical Manual, Page: 6 / 31

Share
Download
Allied Vision Technologies Prosilica GS Series Technical Manual Download Page 6

 

GS1380 Technical Manual

 

Page 6

 

Specifications 

Sensor Type

 

Sony ICX285AL CCD (ICX285AQ for color) 

 

Sensor Shutter Type

 

Progressive Interline 

 

Image Resolution

 

1360 x 1024 pixels

 

Pixel Size

 

6.45μm x 6.45μm

 

Optical Format

 

2/3 inch

 

Lens Mount

 

C-mount with adjustable back focus

 

Color Sensor Filter Pattern

†

 

Bayer

 

Full Resolution Frame Rate

 

30 fps

 

Frame Rate (640 x 480 ROI)

 

55 fps

 

I/O

 

1 isolated input/output, 1 non-isolated input/output,

1 RS-232 input/output

 

Power Requirements

 

Less than 3.5W

††  

(5V to 16V)

†††

 

A/D

 

14 bit

 

Output

 

12 bit

 

Trigger latency*

 

2us for non-isolated I/O, 10us for isolated I/O

 

Trigger Jitter*

 

±20ns for non-isolated I/O, ±0.5us for isolated I/O

 

Tpd*

 

10ns for non-isolated I/O, 1.3us for isolated I/O

 

Operating Temperature

 

0 to 50 Celsius***

 

Operating Humidity

 

20 to 80% non-condensing

 

Weight

 

187g

 

Hardware Interface Standard

 

IEEE 802.3 1000BASE-T, 100BASE-TX

 

Software Interface Standard

 

GigE Vision Standard 1.0

 

Regulatory

 

CE, FCC, RoHS

 

† 

Applies to GS1380C only. 

†† 

Power consumption will increase with reduced ROI imaging and color interpolation. 

††† 

Nominal operating voltage is 12V.  Cameras have been tested at 12V. 

* 

See Notes on Triggering in the Addendum. 

 

 

***DUE TO THE SMALL PACKAGING AND HIGH SPEED OF THE GS CAMERAS, SPECIAL CARE IS REQUIRED TO 

MAINTAIN A REASONABLE OPERATING TEMPERATURE.  IF THE CAMERA IS TO BE OPERATED IN A WARM 
ENVIRONMENT, IT IS SUGGESTED THAT THE CAMERA BE MOUNTED ON A HEAT SINK SUCH AS A METAL BRACKET 
AND THAT THERE IS SUFFICIENT AIR FLOW. 

 

Summary of Contents for Prosilica GS Series
































Reviews:

No comments