manualshive.com logo in svg

Allied Vision Technologies Prosilica GS Series, Technical Manual, Page: 13 / 31

Share
Download
Allied Vision Technologies Prosilica GS Series Technical Manual Download Page 13

 

GS1380 Technical Manual

 

Page 13

 

Isolated Ground 

Isolated Ground must be connected to the user’s external circuit ground if Sync Input 1 or Sync 
Output 1 is to be used.  

Signal Ground 

Signal Ground must be connected to the user’s external circuit ground if Sync Input 2 or Sync 
Output 2 is to be used or if the RS-232 port is to be used.  Note that Signal Ground is common with 
Power Ground however it is good practice to provide a separate ground connection for power and 
signaling when designing the cabling. 

Video Iris 

This signal can be used to drive the video input of a video iris lens. See Addendum. 

DNC 

These signals are reserved for future use and should be left disconnected. 

Item 3: Status LED 1 

  

LED COLOR

 

STATUS

 

 

Solid Orange

 

Ethernet link established.

 

Flashing Orange

 

Ethernet activity.

Item 4: Status LED 2 

  

LED COLOR

 

STATUS

 

 

Solid Green

 

Normal operation.

 

 

Flashing once per second 

 

Boot up pending

 

 

3 quick flashes once per 
second.

 

Camera fault.

 

 

 

Summary of Contents for Prosilica GS Series
































Reviews:

No comments