background image

Patch SB251-10 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches

13

Patch SB251-10 for Software Release 2.5.1
C613-10361-00 REV J

When OSPF was enabled on startup, an OSPF interface would sometimes 
stay in the DOWN state. This issue has been resolved.

The following parameters have been changed CREATE CLASSIFIER, SET 
CLASSIFIER and SHOW CLASSIFIER commands:

The MACTYPE parameter has been changed to 
MACTYPE={L2UCAST|L2MCAST|L2BCAST|ANY}. This resolves 
an error with internal hardware tables.

The number of user-specified protocols in the PROTOCOL parameter 
has been increased from three to seven.

The minimum value of the IPXDADDRESS parameter has been 
decreased from 10000000 to 00000001.

An issue which sometimes resulted in a broadcast storm within the internal 
ports on the SwitchBlade, a reduction in bandwidth, and a loss of pinging 
has been resolved.

An issue which caused pings to fail when a control card was inserted in the 
left hand slot to act as a slave, has been resolved.

Support has been added to allow for multicasting to any number of 
overlapping VLANs up to the maximum number of multicast forwarding 
entries.

An issue with pings failing after network host routes disappeared from the 
switch due to an IP hashing error has been resolved.

An issue with an interrupt occurring when waiting on the MDIO which 
caused the MDIO to read or write incorrect information has been resolved.

Ping would sometimes not work correctly after a 48 line card was extracted, 
and after a restart reboot. This issue has been resolved.

Availability

Patches can be downloaded from the Software Updates area of the Allied 
Telesyn web site at 

www.alliedtelesyn.co.nz/support/updates/patches.html

. A 

licence or password is not required to use a patch.

PCR: 02587

Module: OSPF

Network affecting: No

PCR: 03001

Module: SWI CLASSIFIER

Network affecting: No

PCR: 03006

Module: SWI

Network affecting: No

PCR: 3008

Module: SWI

Network affecting: No

PCR: 03014

Module: IPG, SWI

Network affecting: No

PCR: 03018

Module: SWI

Network affecting: No

PCR: 03020

Module: SWI

Network affecting: No

PCR: 03021

Module: SWI

Network affecting: No

Summary of Contents for SB251-10















Reviews: