Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 161

Page: 161 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section II: Installing the Chassis

161

3. Carefully remove the Ethernet line card from the anti-static bag. Refer

to Figure 90.

Figure 90. Removing an Ethernet Line Card from the Anti-static Bag

4. Align the line card with the internal chassis card guides in the selected

slot in the chassis.

Figure 91 shows an Ethernet line card aligned with slot 1.

Figure 91. Aligning an Ethernet Line Card in a Chassis Slot

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands