manualshive.com logo in svg

Allied Telesis AT-2872SX, Installation And User Manual

Share
Download
Allied Telesis AT-2872SX Installation And User Manual Download Page 76

Appendix B: Cleaning Fiber Optic Connectors

76

Using a Swab

Specially treated swabs (stick cleaners) are available for cleaning inside 
connector adapters or hard-to-reach ferrule tips. These swabs, often 
referred to as “lint free” or “alcohol free” swabs, are available from many 
vendors, as shown in Figure 17. Stick cleaners are available in both 2.5 
mm and 1.25 mm sizes for use on SC and MU connectors respectively.

Note

NEVER use a household cotton swab and/or alcohol to clean a fiber 
optic connector. This may leave a residue on the ferrule tip.

Figure 17. Lint-Free and Alcohol-Free Swabs

Note

Do not use compressed air or aerosol air to clean a fiber optic 
connector.

To clean a recessed ferrule using a swab, do the following.

1. Insert the swab into the adapter as shown in Figure 16 and rub the 

ferrule tip with the swab.

Figure 18. Cleaning a Recessed Ferrule

2. If desired, repeat step 1.

157

Summary of Contents for AT-2872SX















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands