manualshive.com logo in svg

Allied Telesis AT-2872SX, Installation And User Manual

Share
Download
Allied Telesis AT-2872SX Installation And User Manual Download Page 75

AT-2872 SX Gigabit Ethernet Fiber ExpressCard Interface User’s Guide

75

Note

Rub the ferrule tip on the cleaning surface in one direction only.

3. When you reach the end of the cleaning surface, pick up the ferrule tip, 

rotate and place it at the top and rub downwards at least 2 times.

Caution

Failing to pick up the ferrule tip when you reach the bottom of the 
cleaning surface can result in static electricity that can damage the 
fiber optic cable.

4. If desired, repeat steps 3 and 4.

5. If a fiber inspection scope is available, use the scope to inspect the 

ferrule end face to make sure that it is clean.

6. Reconnect the cable to the port or protect the ferrule tip with a dust 

cap.

Note

Always keep a dust cap on a fiber optic cable when it is not in use.

Note

Do not touch the end face of the ferrule in the connector.

Summary of Contents for AT-2872SX















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands