ALLIANCE X Troubleshooting Manual Download Page 35

Page: 35 / 76

201143

Section 4

Control Troubleshooting

Model AWNA62SN301AW01

20. Error Mode

In Error Mode, the

IN USE

LED flashes to display

fill and drain errors (refer to paragraphs below).

Error Mode can only be exited by powering down

washer.

Fill Error

A Fill Error will occur if the tub does not fill

within 62 minutes of the start of the cycle. A Fill

Error is indicated by the control repeatedly

flashing the

IN USE

LED twice separated by a one

and a half second pause until the control is

powered down. If Error Mode is turned off, the fill

error will not occur and the control will continue

to wait for the fill level to be reached.

Drain Error

A Drain Error will occur if the tub is not empty

after a spin cycle. A Drain Error is indicated by the

control repeatedly flashing the

IN USE

LED three

times separated by a one and a half second pause

until the control is powered down. If Error Mode

is turned off, the drain error will not occur and the

machine cycle will advance to the next cycle step

as though the water had been pumped out.

WARNING

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the washer is properly grounded.

W003

Summary of Contents for X













































































Search results

Summary of Contents for X

Reviews:

Related manuals for X

Brands by name

Popular brands

ALLIANCE X, Troubleshooting Manual

Search results

Summary of Contents for X

Reviews:

Related manuals for X

Brands by name

Popular brands