Alliance Laundry Systems ZDE30RGS171CW01 Troubleshooting Manual Download Page 38

Page: 38 / 48

505894

Section 5 Test Procedures

23. DRIVE MOTOR

Refer to

Figure 5

a. Remove motor and exhaust assembly. Refer to

Paragraph 51

b. Disconnect motor wire harness at motor

disconnect block.

NOTE: Refer to wiring schematic, Section 8, for

internal motor switch wires.

NOTE: Drive Motor Resistance

120 Volt

2,460 – 3,100 Ohms

240 Volt

10,000 - 13,000 Ohms

To reduce the risk of electric shock, fire, explosion, serious injury or death:

• Disconnect electric power to the dryer(s) before servicing.

• Close gas shut-off valve to gas dryer(s) before servicing.

• Never start the dryer(s) with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the dryer is properly grounded.

W001R1

WARNING

Figure 5

DRIVE

MOTOR

MOTOR AND

EXHAUST

ASSEMBLY

D326SE3A

MOTOR

DISCONNECT

BLOCK

MOTOR

SWITCH

Summary of Contents for ZDE30RGS171CW01

















































Search results

Summary of Contents for ZDE30RGS171CW01

Reviews:

Related manuals for ZDE30RGS171CW01

Brands by name

Popular brands

Alliance Laundry Systems ZDE30RGS171CW01, Troubleshooting Manual

Search results

Summary of Contents for ZDE30RGS171CW01

Reviews:

Related manuals for ZDE30RGS171CW01

Brands by name

Popular brands