Alliance Laundry Systems BWNBX2PP303AW01 Troubleshooting Manual Download Page 48

Page: 48 / 64

Washer Will Not Fill (Mixing Valve Diagnostic)

E FL

on digital display

NOTE: Make sure unit passes pressure sensor diagnostics first. Refer to

Pressure Sensor Error

Is the lid closed?

(1)

Is there voltage from

the output board to

the lid switch at

"H3-2" to "H1-4"?

Yes

Close lid.

(2)

Is there voltage from

the output board to
the water valves at

"H4-8" (Hot) and

"H4-7" (Cold) to

"H4-1"?

Yes

Check function of lid

switch. Replace if

needed.

(3)

Is there voltage at

the mixing valve

solenoids?

Yes

Replace output board.

Replace mixing valve.

Yes

Check harness for

damage. Replace if

needed.

Troubleshooting Electronic Control

DO NOT COPY or TRANSMIT

Part No. 204591EN

Summary of Contents for BWNBX2PP303AW01

































































Search results

Summary of Contents for BWNBX2PP303AW01

Reviews:

Related manuals for BWNBX2PP303AW01

Brands by name

Popular brands

Alliance Laundry Systems BWNBX2PP303AW01, Troubleshooting Manual

Search results

Summary of Contents for BWNBX2PP303AW01

Reviews:

Related manuals for BWNBX2PP303AW01

Brands by name

Popular brands