Alliance Laundry Systems BWNBX2PP303AW01 Troubleshooting Manual Download Page 38

Page: 38 / 64

Excessive Vibration

Has the shipping plug

been removed from

base?

Is there an

unbalanced load in

tub?

Yes

Remove plug.

Are any centering

springs broken or

disconnected?

Stop washer.

Redistribute load.

Then restart washer.

Yes

Is washer unleveled?

Connect or replace

centering spring(s).

Yes

Is washer installed

on weak, "spongy",

carpeted or built-up

floor?

Adjust leveling legs.

Make sure rear

leveling legs are

free.

Yes

Are cabinet screws

incorrect or loose?

Relocate washer or

support floor to

eliminate weak or

"spongy" condition.

Yes

Is base damaged

(washer was dropped)?

Replace with correct

screws or tighten.

Yes

Is there lubricant on

pivot dome and/or

base friction ring?

Replace base assembly.

Yes

Is partial liquid

filled balance ring

leaking?

Remove lubricant or

replace parts.

Yes

Is friction ring

broken?

Replace balance ring.

Yes

Replace friction ring.

Yes

Troubleshooting Flowcharts

DO NOT COPY or TRANSMIT

Part No. 204591EN

Summary of Contents for BWNBX2PP303AW01

































































Search results

Summary of Contents for BWNBX2PP303AW01

Reviews:

Related manuals for BWNBX2PP303AW01

Brands by name

Popular brands

Alliance Laundry Systems BWNBX2PP303AW01, Troubleshooting Manual

Search results

Summary of Contents for BWNBX2PP303AW01

Reviews:

Related manuals for BWNBX2PP303AW01

Brands by name

Popular brands