manualshive.com logo in svg

Alliance Laundry Systems ATE50FWP431AW01, User Manual

Share
Download
Alliance Laundry Systems ATE50FWP431AW01 User Manual Download Page 81

802848

7

9

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Section 8

Internal Wiring of Dryer Motor Switch

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect all electric power to the machine and accessories before servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start machine with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the machine is properly grounded.

• Washer motor not grounded! Disconnect electric power before servicing motor.

W502

WARNING

Figure 18

R

R

S

2 6

4 3

5

1

MAIN

START

ORANGE/COPPER

CUSTOMER CIRCUIT

OVERLOAD

PROTECTOR

BLUE/BROWN

BLACK/COPPER

YELLOW/COPPER

PUSH TO

START

LINE

SWITCH SHOWN IN START POSITION

R.S.P.C.

2 6

4 3

5

1

G

D329SE3D

G

Motor Switch

Attaching Screws

Summary of Contents for ATE50FWP431AW01



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands