Alliance Laundry Systems 802957R3 Page 37 Installation & Operation Manual Download

Page: 37 / 48

Operation

802957

Indicator Lights

INSERT COINS/CARD

INSERT COINS/CARD

is lit to prompt the user to

insert coins or a card to satisfy the vend price. When

INSERT COINS/CARD

is lit, the digits show the vend

price remaining to be satisfied.

WASH

WASH

is lit during the

WASH

portions of the cycle.

RINSE

RINSE

is lit during the

RINSE

portions of the cycle.

SPIN

SPIN

is lit during the final Spin portion of the cycle..

DOOR

DOOR

is lit whenever the door is locked. The door

cannot be opened when this light is on.

LIGHT

LIGHT

is lit when the

LIGHT

Soil Level is selected.

MEDIUM

MEDIUM

is lit when the

MEDIUM

Soil Level is

selected.

HEAVY

HEAVY

is lit when the

HEAVY

Soil Level is selected.

IMPORTANT: If washer fails to operate properly

after installation, make sure electrical service and

water supply faucets are turned on. Are all the

controls properly set? Have a qualified serviceman

refer to the wiring diagram (located inside of

washer control cabinet), check for broken, loose or

incorrect wiring.

NOTE: Once a cycle has started, the door is locked

and it can only be opened by first unplugging the

power cord and waiting one minute.

To reduce the risk of bodily injury, do not

remove laundry from washer until all lights

are out, and all moving parts have stopped.

W092

WARNING

Summary of Contents for 802957R3

















































Search results

Summary of Contents for 802957R3

Reviews:

Related manuals for 802957R3

Brands by name

Popular brands

Alliance Laundry Systems 802957R3, Installation & Operation Manual

Search results

Summary of Contents for 802957R3

Reviews:

Related manuals for 802957R3

Brands by name

Popular brands