background image

Installation

801455

14

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Water Supply Requirements

NOTE: Water supply faucets must fit standard 

3/4 in. (19.1 mm) female garden hose couplings. 

DO NOT USE SLIP-ON OR CLAMP-ON 

CONNECTIONS.

NOTE: Water supply faucets should be readily 

accessible to permit turning them off when washer 

is not being used.

Water Temperature

Cold:

Recommended cold water temperature is 60° to 

80° Fahrenheit (16° to 27° Celsius).

Hot:

Recommended hot water temperature is 120° to 

140° Fahrenheit (49° to 60° Celsius).

Warm:

Mixture of hot and cold water (warm water 

temperature is dependent upon the water temperature 

and the pressure of both the hot and cold water supply 

lines).

IMPORTANT: Turn off water supply faucets after 

check-out and demonstration. Owner should turn 

off water supply whenever there will be an 

extended period of non-use.

NOTE: Longer fill hoses are available (as optional 

equipment at extra cost) if the hoses (supplied with 

the washer) are not long enough for the 

installation. Order hoses as follows:

No. 20617 Fill Hose (8 ft.) (2.44 m)

No. 20618 Fill Hose (10 ft.) (3.05 m)

Water Pressure

Pressure must be a minimum of 20 to a maximum of 

120 pounds per square inch (138 to 827 kPa) static 

pressure measured at the faucet.

NOTE: Water pressure under 20 pounds per 

square inch (138 kPa) will cause an extended fill 

time in the washer and may not properly flush out 

the detergent dispenser.

Risers

Risers (or air cushions) may have to be installed if the 

pipes knock or pound when flow of water stops. The 

risers are more efficient when installed as close as 

possible to the water supply faucets (refer to 

Figure 20

).

Under certain conditions, hydrogen gas may 

be produced in a hot water system that has 

not been used for two weeks or more. 

HYDROGEN GAS IS EXPLOSIVE. If the hot 

water system has not been used for such a 

period and before using the washer, turn on 

all hot water faucets and let the water flow 

from each for several minutes. This will 

release any accumulated hydrogen gas. The 

gas is flammable. Do not smoke or use an 

open flame during this time.

W029

WARNING

FLW1973N

1

Water Supply Faucets

2

Cold Water Connection

3

Hot Water Connection

4

Fill Hoses

Figure 19 

W005I

1

Water Supply Faucets

2

Risers (Air Cushions)

Figure 20 

FLW1973N

1

2

3

WATER 
MIXING 

VALVE

4

W005I

2

1

Summary of Contents for 801455R2





















Reviews: