manualshive.com logo in svg

allen 069600, Safety & Operation Manual

The "Allen 069600" Safety & Operation Manual is an essential guide for users, providing step-by-step instructions on how to safely operate the product. This comprehensive manual is available for free download at manualshive.com, ensuring that users have all the necessary information to utilize the product efficiently and without any mishaps.

Share
Download
background image

•  When lifting the machine, all personnel must be clear of the machine.

•  DO NOT

 stand near or under the machine while it is being lifted.

Lifting instructions using a hoist:

•  An optional lifting harness is available for purchase. Part number 064798

•  Place slings, chains or hooks through each lifting point on the machine. Use a sling or chains connected to a central 

lifting device. Ensure that all lifting devices have sufficient weight-bearing capacity.

•  ALWAYS

 shutdown engine before transporting.

LIFTING POINT

SECTION 1

SAFETY

069971

Page 20

Lifting Safety

Summary of Contents for 069600





























































Reviews:

No comments

Related manuals for 069600

Brands by name

Popular brands

Load more brands