Allen-Bradley MicroLogix 1762-IQ8 Installation Instructions Manual Download Page 2

2

MicroLogix™ 1762-IQ8 DC Input Module 

1762-IN004A-US-P 

For More Information

If you would like a manual, you can:

download a free electronic version from the internet: 

www.ab.com/micrologix

 or 

www.theautomationbookstore.com

purchase a printed manual by:
– contacting your local distributor or Rockwell Automation representative
– visiting 

www.theautomationbookstore.com

 and placing your order

– calling 

1.800.963.9548

 (USA/Canada) 

or 

001.330.725.1574

 (Outside USA/Canada)

For

Refer to this Document

Pub. No.

Information on installing, wiring, and 
operating a MicroLogix 1200 
Programmable Controller

MicroLogix 1200 Programmable 
Controllers User Manual

1762-UM001A-US-P

Installation guide for the MicroLogix 
1200 Programmable Controller.

MicroLogix 1200 Programmable 
Controllers Installation 
Instructions

1762-IN006A-ML-P

Installation guide for the MicroLogix 
1200 Memory Module and Real Time 
Clock.

MicroLogix 1200 Memory 
Module and/or Real Time Clock 
Installation Instructions

1762-IN001A-US-P

Installation guide for the 1762-IA8 
Discrete Input Module

1762-IA8 120V ac Input Module 
Installation Instructions

1762-IN002A-US-P

Installation guide for the 1762-OW8 
Discrete Output Module

1762-OW8 Relay Output Module 
Installation Instructions

1762-IN003A-US-P

Installation guide for the 1762-IF2OF2 
Analog I/O Module

1762-IF2OF2 Analog Input/
Output Module Installation 
Instructions

1762-IN005A-US-P

More information on proper wiring and 
grounding techniques.

Industrial Automation Wiring 
and Grounding Guidelines

1770-4.1

Summary of Contents for MicroLogix 1762-IQ8

















Reviews: