Allen-Bradley Bulletin 2364F Troubleshooting Manual Download Page 59 | Manualshive

Page: 59 / 64

background image

Publication 2364F-5.05 - March 1999

Glossary

1336 FORCE Adjustable Frequency AC Drive

An adjustable frequency AC drive produced by Rockwell Automation. Most of the
construction and components of the RGU power structure are equivalent to the
1336 FORCE drive.

Control Power Filter

A filter used to reduce harmonics and noise in the 115V AC control power.

Digital Signal Processor (DSP)

The digital signal processor which is located on the main control board of the RGU.
This component processes current commands for the RGU.

Disable

When a unit is disabled, the control logic is not directing current flow operations. A
unit is typically disabled by a disable command or by a fault condition.

Disconnect

A circuit breaking device.

Enable

When a unit is enabled, the control logic is directing the motoring or regenerative
current by modulating its hardware (IGBTs).

Feedback

Signals from the hardware which indicate the hardware status to the control logic.

Gate Driver Board

The RGU gate driver board is responsible for modulating the power modules and
supplying power to the control boards. The gate driver board is interfaced with the
main control board.

Graphic Programming Terminal (GPT)

A programming terminal with a graphical LED display and a pushbutton keyboard
which is used to program, control, and view the status of a unit. The GPT is also
able to load and store parameters in its local memory.

Host Processor

The main processor on the main control board of the RGU. This component
processes feedback and controls most of the activities in the RGU.

Human Interface Module (HIM)

A programming terminal used to program, control, and view the status of a unit.

Insulated Gate Bipolar Transistor (IGBT)

A transistor which can be used to allow current to flow in two opposite directions.
Also known as power module.

Isolation Board

The RGU isolation board receives direct feedback from the AC line, DC bus, and
current transducers. This board supplies scaled feedback to the main control board.

«
...
57
58
59
60
61
...
»

Summary of Contents for Bulletin 2364F

































































Reviews:

No comments

Related manuals for Bulletin 2364F

Brand: ZOLL Pages: 344

Brand: ABB Pages: 9

Brand: Eclipse Combustion Pages: 46

Brand: Bard Pages: 2

Brand: GE Pages: 14

Brand: GE Pages: 11

Brand: GE Pages: 20

Druck ADTS 2 Series

Brand: GE Pages: 18

Brand: Bartscher Pages: 28

Brand: Bartscher Pages: 13

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

Brand: Kawai Pages: 10

Brand: fadini Pages: 20

Brand: Garelick Pages: 4

Tablet1000 Series

Brand: Hantek Pages: 98

NI VISION PCI-8254R

Brand: National Instruments Pages: 13

NI VISION PCI-8254R

Brand: National Instruments Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands