Allen-Bradley 5069-IA16 User Manual Download

Page: 268 / 296

268

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Appendix B

Module Tag Definitions

5069-IB8S and 5069-IB8SK
Module Tags

This section describes the tags that are associated with the 5069-IB8S or
5069-IB8SK module.

Input Tags

Table 89

describes the 5069-IB8S or 5069-IB8SK module input tags.

5069-OBV8S

SIL2 CPU

5069-L3100ERMS2

Compact GuardLogix

5069-OBV8S

5069-IB8S

OUTPUT

SA P

MOD P

Safety Modules

Table 89 - 5069-IB8S or 5069-IB8SK Module Input Tags

Name

Data Type

Definition

Valid Values

RunMode

BOOL

Module’s operating state

• 0 = Idle
• 1 = Run

ConnectionFaulted

BOOL

Indicates if a connection is running.
The module sets this tag to 0 when connected. If the
module is not connected, it changes the tag to 1.

• 0 = Connection running
• 1 = Connection not running

DiagnosticActive

BOOL

Indicates if any diagnostics are active or if the prognostics
threshold is reached.

• 0 = No diagnostics active

• 1 = One or more diagnostics are active or the

prognostics threshold is reached

DiagnosticSequenceCount

SINT

Increments for each time a distinct diagnostic condition is
detected, and when a distinct diagnostic condition
transitions from detected to not detected.
Set to zero by product reset or power cycle. Wraps from
255 (-1) to 1 skipping zero.

• 1…255
The value of 0 is skipped except during module
power-up.

Ptxx.Data

BOOL

Indicates the current safety input value.

• 0 = Off
• 1 = On

Ptxx.Fault

BOOL

Indicates one of the following:

• The channel data is inaccurate and

cannot be trusted

for use in the application.
For more information, see

Module Data

Quality Reporting on page 71

• The channel is set to Not Used.

• 0 = Good data
• 1 = Bad data (faulted) or set to Not Used

If the tag is set to 1, you must troubleshoot the
module to correct the cause of the inaccuracy.

IMPORTANT

: Once the condition that causes

the tag to change to 1 is removed, you must
complete the steps described in

Safety Input

Fault Recovery on page 138

to reset this tag

to 0.
If the tag is 1 because the channel is set to Not
Used, no action is required.

Ptxx.Uncertain

BOOL

Indicates that the channel data can be inaccurate but the

degree of inaccuracy is not known

For more information, see

Module Data Quality Reporting

on page 71

• 0 = Good data

• 1 = Uncertain data

This tag is set to 1 when the module has
reached a critical operating temperature or is
higher the acceptable operating temperature.

IMPORTANT

: Once the condition that causes

the tag to change to 1 is removed, the tag
automatically resets to 0.

Ptxx.ShortCircuit

BOOL

Indicates a short circuit.

• 0 = No short circuit
• 1 = Short circuit

Ptxx.Status

BOOL

Indicates the status of the channel.

• 0 = Bad, causing a fault
• 1 = Good

Testxx.Readback

BOOL

Indicates that a 24V DC power source is present at the
test output.

• 0 = 24V DC power is not present
• 1 = 24V DC power is present

Summary of Contents for 5069-IA16









































































































































































































































































































Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands

Allen-Bradley 5069-IA16, User Manual

Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands