Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 138 / 296

background image

138

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 5

Safety Module Features

Safety Input Fault Recovery

If an error is detected, the safety input data remains in the OFF state. To
activate the safety input data again, complete the following steps.

1. Remove the cause of the error.

2. Place the safety input (or safety inputs) into the safe state.

3. Allow the Input Error Latch Time and another 10 seconds to elapse.

After the steps are completed, the I/O indicator (red) turns off. The input data
is now active.

Safety Input Delay Time

You can increase the time that it takes for an input point to transition from On
to Off and Off to On on the 5069-IB8S or 5069-IB8SK module. The increase
in time is a delay of the signal from the module to the controller.

The delay time is in addition to the RPI, the parameter that defines a rate at
which the owner-controller and the module exchange data (2…500 ms). For
example, if you set the RPI at 10 ms and use an input delay time of 2 ms, the
signal from the module to the controller is 12 ms.

An increase in the time it takes to transition from one state to another
improves noise immunity within a signal.

«
...
136
137
138
139
140
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: zipwake Pages: 12

Brand: jbc Pages: 12

Brand: Wayne Pages: 16

Aqua-Pure AP510

Brand: 3M Pages: 16

Brand: Ravaglioli Pages: 90

Xsential QUAD-RO

Brand: Watermark Pages: 8

Brand: BERNSTEIN Pages: 52

ETR 2000 series

Brand: Delco Pages: 34

Easy Chime OUKQH-0761

Brand: 1byone Pages: 7

Brand: Comelit Pages: 32

Brand: Microlab Pages: 4

Brand: HIKVISION Pages: 5

Brand: TCS Pages: 12

Brand: iCONNECT Pages: 20

Reflex Wheel-X 50 050 0030

Brand: Carson Pages: 52

Brand: Magnavox Pages: 12

Brand: Vimar Pages: 52

Brand: Trevi Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands