manualshive.com logo in svg

Allen-Bradley 2-D, User Manual

Share
Download
Allen-Bradley 2-D User Manual Download Page 77

5–16

Communication Setup (Synapse Cable)

Publication 2755-6.4

Setting DEC VT220 / VT320 / VT420 Keyboard Wedge 
Synapse Cable Options

This section defines the communication options available when the
scanner is connected to this DEC Keyboard Wedge Synapse cable:

•

Catalog No. 2755-HFC-SV1-01

Default Settings

Scan the Set DEC VT 20/320/420 Wedge Synapse Cable Defaults
bar code to set the Synapse cable to default settings.  The table below
lists the defaults.

Parameter

Default Setting

Refer to

Description 

on Page:

Programming

Guide 

➀

Page Reference

Host

DEC VT220 / 320

5–16

5-2

Country

North American

5–17

5-2

Unknown Characters

Send Bar Codes With
Unknown Characters

5–17

5-4

Intercharacter Delay

5 Millisecond

5–17

5-4

Parameter Set

Parameter Set 1

5–18

5-5

➀ 

Programming Guide for 2-D Bar Code Scanners (Publication 2755-6.7)

Host Selection

Select the type of host the scanner will be communicating with.  
The selections are:

•

DEC VT 220/320 (default)

•

DEC VT420

Summary of Contents for 2-D







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands