manualshive.com logo in svg

Allen-Bradley 2-D, User Manual

Share
Download
Allen-Bradley 2-D User Manual Download Page 18

Scanner Features

1–7

Publication 2755-6.4

Configuration Options

The scanner is adaptable to a wide variety of applications by
scanning configuration bar codes.  The configuration bar codes
control the operation of:

•

decoding

•

scanning

•

communications

The 2-D scanner provides full host compatiblility through a Synapse
cable with programmable options.

Chapters 4 and 5 describe the configuration options.

Decoding

The scanner can decode the following symbologies:

•

One-Dimensional Bar Codes

–

UPC-A, UPC-E

–

EAN-8, EAN-13

–

Code 39, Code 39 Full ASCII

–

Interleaved 2 of 5

–

Code 128

–

Codabar

–

UCC/EAN 128

•

Two-Dimensional Bar Codes

–

PDF417

The scanner is autodiscriminating so that multiple symbologies may
be enabled at the same time.  The only exception is the scanner
cannot discriminate between Code 39 and Code 39 Full ASCII.

Summary of Contents for 2-D







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands