Allen-Bradley 1771-IB Installation Data Download Page 6

Specifications

DC (12-24V) Input Module

Cat. No. 1771-IB

Installation Data

 6

Inputs per Module

8

Module Location

1771 I/O chassis

Input Voltage Range

10 to 27V dc

Nominal Input Current

8mA at 12V dc

24mA at 24V dc

Maximum Off-state Current

3.0mA

Maximum Off-state Voltage

7.0V dc

Minimum On-state Voltage

10V dc

Input Impedance

1 to 2K ohms maximum (on-state)

2 to 3K ohms maximum (off-state)

Input Signal Delay

Low to high propagation delay 12ms +7ms

High to low propagation delay 20ms +7ms

Power Dissipation

5.7 Watts (max.), 0.4 Watts (min.)

Thermal Dissipation

19.3 BTU/hr (max.), 1.4 BTU/hr (min.)

Backplane Current

74mA @ 5V dc  +5%

Opto-electrical Isolation

1500V ac rms

Environmental Conditions

Operational Temperature

Storage Temperature

Relative Humidity

0

o

 to 60

o

C (32

o

 to 140

o

F)

-40

o

 to 85

o

C (-40

o

 to 185

o

F)

5 to 95% (without condensation)

Conductors

Wire Size

Category

14 gage stranded maximum

3/64 inch insulation maximum

2

1

Keying

Between 4 and 6

Between 14 and 16

Field Wiring Arm

Catalog Number 1771-WA

1

 

Refer to publication 1770-4.1, Programmable Controller Wiring and Grounding Guidelines.

With offices in major cities worldwide

WORLD
HEADQUARTERS
Allen-Bradley
1201 South Second Street
Milwaukee, WI 53204 USA
Tel: (1) 414 382-2000
Telex: 43 11 016
FAX: (1) 414 382-4444

EUROPE/MIDDLE
EAST/AFRICA
HEADQUARTERS
Allen-Bradley Europe B.V.
Amsterdamseweg 15
1422 AC Uithoorn
The Netherlands
Tel: (31) 2975/43500
Telex: (844) 18042
FAX: (31) 2975/60222

ASIA/PACIFIC
HEADQUARTERS
Allen-Bradley (Hong Kong)
Limited
Room 1006, Block B, Sea
View Estate
28 Watson Road
Hong Kong
Tel: (852) 887-4788
Telex: (780) 64347
FAX: (852) 510-9436

CANADA
HEADQUARTERS
Allen-Bradley Canada
Limited
135 Dundas Street
Cambridge, Ontario N1R
5X1
Canada
Tel: (1) 519 623-1810
FAX: (1) 519 623-8930

LATIN AMERICA
HEADQUARTERS
Allen-Bradley
1201 South Second Street
Milwaukee, WI 53204 USA
Tel: (1) 414 382-2000
Telex: 43 11 016
FAX: (1) 414 382-2400

As a subsidiary of Rockwell International, one of the world’s largest technology
companies — Allen-Bradley meets today’s challenges of industrial automation with over
85 years of practical plant-floor experience. More than 11,000 employees throughout the
world design, manufacture and apply a wide range of control and automation products
and supporting services to help our customers continuously improve quality, productivity
and time to market. These products and  services not only control individual machines but
integrate the manufacturing process, while providing access to vital plant floor data that
can be used to support decision-making throughout the enterprise.

Publication 1771–2.4 – May 1990

Supersedes publication 1771–2.4 – January 1986 and 1771–2.4–DU1 – October 1987

PN 955107–15

Copyright 1991 Allen-Bradley Company, Inc.   Printed in USA

Summary of Contents for 1771-IB







Reviews: