background image

3 Mounting the terminal

© 2022 Interflex Datensysteme GmbH | IF-5835 Time Recording Terminal | 07.22

8

Installation site

Please observe the following recommendations:

n

Permitted ambient conditions for the device

n

Minimum distance of 10 cm between the connecting cables and the nearest power cable

n

Installation height 1200 mm

Minimum distances between RFID and BLE devices

If several RFID devices are mounted too close together, mutual interference may occur.
Thus, the following minimum distances must be maintained:

The minimum distance for back-to-back installation depends on the nature of the wall in
between.

Please note that all BLE devices within range are recognized and that the respective doors
open too (according to the permission) when the "auto-booking" function is enabled.

3.2 Fastening the back panel of the housing

The following figure shows the back panel of the housing and its side view with appliance case and
mounted terminal as an example.

1

1

2

3

1

4

3

5

6

7

1

3 bore holes for wall mounting

2

Threaded bushing for fastening an
optional 24 V interface (75-5735-0004)

Summary of Contents for interflex IF-5835





























Reviews: