background image

22

Owner’s Manual

Compressor (cont’d)

OPERATING INSTRUCTIONS

 

 

 

 

WARNING!

 HIGH TEMPERATURES ARE GENERATED BY THE 

ELECTRICAL MOTOR AND THE PUMP. TO PREVENT BURNS OR OTHER
INJURYS, DO NOT TOUCH THE COMPRESSOR WHILE IT IS RUNNING. ALLOW  
IT TO COOL BEFORE HANDLING OR SERVICING. KEEP CHILDREN AWAY FROM 
THE COMPRESSOR AT ALL TIMES.

 

 

WARNING!

 WHEN ADJUSTING FROM A HIGHER TO A LOWER

PRESSURE, TURN THE KNOB COUNTERCLOCKWISE TO REACH THE DESIRED 
PRESSURE. DO NOT EXCEED OPERATING PRESSURE OF THE TOOL OR
ACCESSORY BEING USED.

5. Adjust the regulator to the working pressure of the tool. (never exceed 90 PSI)

Shut down

1. Turn the power switch to the OFF position.
2. Unplug the power cord.
3. Reduce pressure in the tank thorough the outlet hose .You can also pull the relief
    valve ring and keep it open in the tank.

 

 

WARNING!

 ESCAPING AIR AND MOISTURE CAN PROPEL DEBRIS 

THAT MAY CAUSE EYE INJURY. WEAR SAFETY GOGGLES WHEN OPENING 
PETCOCK

4. Tip the compressor (if necessary for your model ) so the petcock is at the bottom of
    the tank(S).Then open the petcock to allow moisture to drain from the tank.

Summary of Contents for APC4006

































Reviews: