All Paws Pet Wash ADA813 Manual Download Page 3

Page: 3 / 14

8642 US Highway 20 Garden Prairie, IL 61038

Seller warrants the welded aluminum components for 5 years from date of shipment from our
factory in Garden Prairie, IL.

All other components warranted for 1 year from date of shipment.

Powder coat ﬁnish is excluded from all warranties.

Purchaser shall notify seller of defect in writing and return the defective part for repair or
replacement.

All warranty claims are to be handled by the purchaser. The purchaser will return the non-
working part to the factory [8642 US Hwy 20 Garden Prairie, IL 61038] for repair or
replacement. All Paws Pet Wash will ship the repaired or replaced part back to the purchaser.

Purchaser is responsible for the shipping charge to return to seller and seller is responsible
for shipping charge to return to purchaser.

Labor charges are not included.

Any defect or failure caused by mistreatment or neglect is speciﬁcally excluded under this

warranty. This includes damages caused by freezing.

Depending on water source, All Paws Pet Wash recommends using a pre-ﬁlter.

The seller and purchaser agree that there are no other warranties or representations made by

or on behalf of the seller other than those speciﬁcally set forth in this document. Seller will in

no event be liable for special or consequential damages. This agreement shall be governed
by the laws of the State of Illinois and is deemed entered into in the County of Boone, State
of Illinois. The seller and purchaser agree that jurisdiction of any controversy under this

agreement shall be exclusively in the Courts of the County of Boone, State of Illinois.

Purchaser may contact All Paws Pet Wash factory at (800)537-8231.

Keith Caldwell

Date: 1/1/17 - Present

*information subject to change

Phone:

(800)537-8231

Email:

[email protected]

Web:

www.allpawspetwash.com

Fax:

(815)544-4353

WARRANTY - ADA 813 & ADA 821

8642 US Highway 20 Garden Prairie, IL 61038

• Dog parks
• Campgrounds
• RV parks
• Laundromats
• Gas Stations

• Large Complexes

• Pet Stores
• Groomers
• Kennels
• Pet Friendly Hotels
• Veterinary Hospital
• Car Washes

The ADA Modular buildings are the ﬂagship products of All Paws Pet Wash. It is a piece

of self-serve pet washing equipment that can be implemented and used in many different
industries. These units are built with the quality and precision that our other products have
been built with since 2009. The ADA is built out of the best quality aluminum and is sand blasted

then powder coated for a smooth ﬁnish. APPW offers six different treatments as well as a

grooming blow dryer. It provides an affordable way for a customer to wash their pet without
having to worry about messing up their own home or emptying their wallets.

• No ramps easy for pet to enter low wash tub or wash directly on ﬂoor
• Six wash cycles (Oat, Tearless, Flea & Tick Shampoos,

Conditioner, Pet Deodorizer, Tub Disinfectant)
• High volume rinse
• Groomer-grade blow dryer
• Accepts quarters, tokens, dollar coins, and 1-20 dollar bills with credit card option.

• Non-slip mat in tub and on ﬂoor

• Filtration system to separate hair
• Easy to read directions and push button operation for customers
• Customizable color and decals

• 1/2” or 3/4” Hot/Cold water lines 1/2” NPTF
• Water usage less than 2 gallons per minute
• 220 Volt - 100 amp electric supply

• Weight: Single 813: Approx 2600*

Double 821: Approx 4000*

*Depending on options

• Building numbers refer to dimensions:

single 813 = 8’ x 13’ double 821 = 8’ x 21’

• Tub: 53” long x 26” wide x 6” deep

• Stand alone equipment room enclosed inside the building
• Easy to hook up to utilities

• Sloping tub and sloping ﬂoor leads to ﬂoor trough under wall

for easy cleaning and drainage of water/hair

• Two inch drain for constant ﬂow through hair strainers

• Ability to bypass payment with washdown switch

• Ability to change price and time to ﬁt any market

• Easy to read directions for customers
• ADA Compliance

OWNER/OPERATOR BENEFITS

PARTNER WITH

EQUIPMENT

SPECIFICATIONS

Problem:

No water pressure ﬂow in the wash tub.

Solution:

Check water ﬂow from incoming water line. Check pressure gauge on water column

in cabinet of APW. The unit requires 40-50 PSI to function properly. If you have sufﬁcient ﬂow

form the incoming water line, and 40-50 PSI of required pressure, you will need to adjust the

ﬂow screw [

Reference image on page 3 / #4 Inside Cabinet

]. Start by counting the number of

turns it takes to close the screw when tightening (clockwise). The ﬂow at the wash tub should
not be very low. Now loosen the screw (turning counter-clockwise) approximately 1

- 2

turns, which should increase the ﬂow. Keep in mind the more you loosen the ﬂow screw to the
left the more you will increase the ﬂow, but will be decreasing the suction for the shampoo.

Problem:

One of the shampoos or treatments in not ﬂowing correctly.

Solution:

With the sprayer in the on and locked position, select the soap or treatment that’s

malfunctioning. If everything is working properly, you should have a low pressure ﬂow with

soap and water. If you’re not receiving any soap along with the water, head to the equipment
room and locate the soap containers. Screw off the cap of the soap or treatment that’s mal-

functioning and examine the suction strainer. Make sure the screen is clean, if not, run the

suction strainer under some clean water. Next, examine the clear tube running from the soap

to the water column. If you are getting air bubbles in the tube, the soap is ﬂowing but your

concentrate may be too diluted to see the soap coming out of the sprayer. If you are still

having issues you can increase the ﬂow by loosening the material volume screw.

Problem:

Vacuum is running, but has no suction.

Solution:

Check the hose for obstruction. With the vacuum cleaner off, use the water

ﬂush valve and ﬂush the vacuum. Make sure water is ﬂowing out of the vacuum. Once

completed, run the vacuum and check for suction. If you still do not have suction, you will

need to remove and clean the vacuum motor and ﬁlter. You can also remove the black drain

hose from the check valve at the bottom of the vacuum and then turn on the vacuum. At this
point feel if you are achieving suction back threw the check valve. If you are the check valve

ﬂap is not sealing tight and needs to either cleaned or replaced. Clean the ﬁlters as needed.

Problem:

Water is not pumping out of the hair strainer tank.

Solution:

The pump ﬂoat switch is stuck. Simply unlodge the pump ﬂoat. Rinse out tank as

needed.

Problem:

Floor pumps are not functioning correctly.

Solution:

Ensure that hair is not clogging the release hole at the base of the ﬂoor pump tube.

If clear, spray water directly at the probes to remove any excess ﬁlm build-up. When ﬁlm

accumulates, the build-up will not allow the probes to function properly.