background image

ACRYLIC SHEET

The acrylic sheet should only be removed
when the equipment is at room
temperature.

1.

Should you need to remove the acrylic
sheet, you must proceed as follows:

 

Remove the plug from the power
socket.

 

Unscrew the 4 screws (A) in the end
piece (B).

 

Slide the end piece out of the canopy.
Repeat this procedure with the end
piece at the other end of the equipment.

 

Now rotate the canopy as far as it will
go, so that the lamps are facing
upwards.

2.

 

Carefully free one side of the acrylic
sheet (A) by pulling it out of the plastic
profile (B).

 

Now pull the acrylic sheet towards you
such that it slides out of the plastic
profile at the other side.

3.

When replacing the acrylic sheet, proceed
as follows:

 

Slide the acrylic sheet into the groove in
the plastic profile at one side.

 

Press down on the centre of the acrylic
sheet then slide its free edge into the
groove in the plastic profile on the other
side.

 

Next rotate the canopy all the way
back, such that the lamps are facing
downwards again.

 

Now fit both end pieces using the 4
screws.

PARTS

Use only original Alisun replacement parts:

Part

Art.no.

Brilliant Sun plus XT 100W

350377

GoldSun DuoTan®

Professional 100W

350366

Reflector Salsa 10/12

332220

Timer

355005

This equipment's mains lead may only be
replaced by authorized personnel.

Summary of Contents for Sun lounge Salsa 10















Reviews: