background image

To prevent any hazard during operation of Alinco’s radio product, in this 

manual and on the product you may find symbols shown below. Please 

read and understand the meanings of these symbols before starting to 
use the product.

Danger

This symbol is intended to alert the user to an 
immediate danger that may cause loss of life and 
property if the user disregards the warning.

Alert

This symbol is intended to alert the user to a possible 
hazard that may cause loss of life and property if the 
user disregards the warning.

Caution

This symbol is intended to alert the user a possible 
hazard that may cause loss of property or injure the 
user if the warning is disregarded.

Alert symbol. An explanation is given.

Warning symbol. An explanation is given.

Instruction symbol. An explanation is given.

ALERT

Environment and condition of use:

Do not drive while handling the radio for your safety. It is 

recommended that you check local traffic regulations regarding 

the use of radio equipment while driving.

Some countries prohibit the operation of transceiver while driving.

Do not use this product in close proximity to other electronics 
devices, especially medical ones. It may cause interference 
to those devices.

Keep the radio out of the reach of children.

In case a liquid leaks from the product, do not touch it. It may 
damage your skin.
Rinse with plenty of cold water if the liquid contacted your 
skin.

Never operate this product in facilities where radio products 
are prohibited for use such as aboard aircraft, in airports, in 
ports, within or near the operating area of business wireless 
stations or their relay stations.

Use of this product may be prohibited or illegal outside of 
your country. Be informed in advance when you travel.

The manufacturer declines any responsibilities against 
loss of life and/or property due to a failure of this product 
when used to perform important tasks like life-guarding, 
surveillance, and rescue.

Do not use multiple radios in very close proximity. It may 
cause interference and/or damage to the product(s).

The manufacturer declines any responsibilities against loss 
of life and property due to a failure of this product when used 
with or as a part of a device made by third parties.

Use of third party accessory may result in damage to this 
product. It will void our warranty for repair.

WARNING

Summary of Contents for DX-10













































Reviews: