Alinco DR-235T User Manual Download Page 9

Page: 9 / 10

DISPLAY

SQL

Appears when setting the squelch level.

Appears when in memory mode

Indicates the memory no. in memory mode

.Decimal point Appears when setting the burglar alarm function.

. Decimal point

Appears when setting the decimal point of skip level.

. Decimal point

Indicates the decimal point of frequency and the scanning movement.

8888888

Indicates the frequency and memory name

BUSY Appears when signal is being receive.

S-meter

Indicates the signal strength level of transmission / reception.

Appears when in 9600 bps packet mode.

Appears when setting the key lock.

DCS

Appears when setting the DCS.

TSQ

Appears when setting the tone squelch

㧗㧙

Appears when setting the shift.

Appears during AM reception.

Nar

Appears when in narrow band reception mode

Appears when transmission power is set to LOW

㧚

Appears when transmission power is set to MID

Appears when FUNC Key is pressed.

Summary of Contents for DR-235T











Search results

Summary of Contents for DR-235T

Reviews:

Related manuals for DR-235T

Brands by name

Popular brands

Alinco DR-235T, User Manual

Search results

Summary of Contents for DR-235T

Reviews:

Related manuals for DR-235T

Brands by name

Popular brands