Alienware Aurora Ryzen Edition R14 Service Manual Download Page 46

Page: 46 / 98

Steps
1. Remove the screw (M2x3) that secures the 2280 solid-state drive to the system board.
2. Slide and lift the 2280 solid-state drive off the system board.

Installing the 2280 solid-state drive

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

CAUTION: Solid-state drives are fragile. Exercise care when handling the solid-state drive.

About this task

NOTE: This procedure applies only to computers shipped with a 2280 solid-state drive installed in the SSD slot.

NOTE: Depending on the configuration ordered, your computer may support either 2280 solid-state drive or 2230 solid-state
drive in the SSD slot.

If you want to replace your 2280 solid-state drive with a 2230 solid-state drive, see

Installing the 2230 solid-state drive

The following images indicate the location of the 2280 solid-state drive and provide a visual representation of the installation

procedure.

Summary of Contents for Aurora Ryzen Edition R14



































































































Search results

Summary of Contents for Aurora Ryzen Edition R14

Reviews:

Related manuals for Aurora Ryzen Edition R14

Brands by name

Popular brands

Alienware Aurora Ryzen Edition R14, Service Manual

Search results

Summary of Contents for Aurora Ryzen Edition R14

Reviews:

Related manuals for Aurora Ryzen Edition R14

Brands by name

Popular brands