5
www.Observint.com
© 2017, 2018 Observint Technologies. All rights reserved.
Camera
Specification
Video
Video Compression Format
H.264+ / H.264 / MJPEG
Codec Streaming
Capability
Dual Streaming
Maximum Frame Rate
Mode 1: Up to 30 fps (4096 × 1800, 3840× 1680)
Mode 2: Up to 24 fps (2400 × 3840), 30 fps (1200 × 1920)
Bit Rate
32 kbps ~ 16 Mbps
Bit Rate Mode
CBR, VBR
Audio
Audio Streaming
Two-way
Audio Compression Format
G.711 / G.722.1 / G.726 / MP2L2
Features
Motion Detection
Support, zone configurable
Backlight Compensation
Support
Event Notification
Alarm Output, Email, FTP
Privacy Mask
Support
ROI Encoding
Support
Defog
Support
Tampering Detection
Support
Interface
Ethernet
RJ-45 10/100 BASE-T
Audio Input
1x 3.5 mm audio in
Audio Output
1x 3.5 mm audio out
Sensor Input
1x In
Alarm Output
1x Out (up to 24 Vdc, 1A or 24 Vac, 500 mA)
SD Card Slot
1x Micro SD/SDHC/SDXC (up to 128GB)
Network
Protocols
TCP/IP, UDP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP, UPnP, SMTP,
SNMP, IGMP, 802.1X, QoS, IPv6, Bonjour
Security
One-key reset, flash-prevention, dual streams, heartbeat, mirror, password protection, privacy
mask, Watermark, IP address filtering, Anonymous access
Network Storage
NAS (Support NFS, CIFS/SMB)
General
Power Requirements
12 Vdc± 10%, 22 W max
PoE+ (802.3af Class 3)
Weight
6.28 bs
Dimensions
7.68 Φ x 6.26” H
Operating Temperature
-22°F ~ 140°F
Operating Humidity
0% ~ 95% RH, Non-condensing
Ingress Protection
IP66
Impact Protection
IK10
Color
White
Material
Aluminum (body), Polycarbonate (bubble)
Approvals
CE, FCC, RoHS, UL
System Requirements
Operating System
Windows XP / VISTA / 7 / 8 / 10, Mac OSX
Processor
Intel Pentium 4 3.0 GHz or faster
Memory
Built-in microSD / SDHC / SDXC slot, up to 128GB
Display
1024 x 768 resolution or higher
Web Browser
Internet Explorer 6.0 or above, Apple Safari 5.02 or above, Mozilla Firefox 3.5 or above
Supplied Accessories
Quick Installation Guide
Mounting Hardware and Template
Using the Waterproof Ethernet Fitting
Install the
Waterproof Ethernet Fitting
on the Ethernet cable end at the camera when moisture or
contamination exists in the area near the camera. The fitting includes several parts that must be installed in
a specific order. To install the fitting:
1.
Place the rubber O-ring over the camera drop cable end cap.
Push the O-ring up to the connector cap.
2.
If the network cable from the switch or router has a connector
on the end, cut off the connector.
3.
Place the Lock Nut onto the network cable from the router
or switch as shown in the drawing to the right. The inside
threads must be toward the camera end.
4.
Place the rubber basket onto the network cable above the lock
nut as shown.
5.
Place the end cap onto the network cable above the rubber
gasket as shown. The fingered end must be toward the router
or switch.
6.
Install an RJ-45 connector onto the network cable.
7.
Plug the RJ-45 connector with the network cable into the
camera network drop cable.
8.
Fit the end cap on the network cable onto the camera drop
cable end cap. Rotate the network cable end cap to lock it in
place.
9.
Push the rubber gasket fully into the end of the network cable
end cap.
10. Screw the lock nut onto the network cable end cap until it is
fully seated.
Network drop
cable from
camera
Network cable from
router or switch
Ethernet Fitting installed
Waterproof Ethernet Fitting assembled and connected
Drop cable
end cap
Network drop
cable from
camera
Rubber
O-ring
seal
RJ-45
connector
End cap
Rubber
gasket
Network
cable
from
router or
switch
Lock nut
