manualshive.com logo in svg

Algo 8180, User Manual

Share
Download
Algo 8180 User Manual Download Page 28

- 28 -

Provisioning

 

 

Provisioning allows installers to pre-configure 8180 units prior to installa

-

tion on a network. It is typically used for large deployments to save time 

and ensure consistent setups.

There are two different Provisioning methods that can be used: via 

DHCP Option 66 or via a Static Server. In addition, there are three 

different ways to download provisioning files from a “Provisioning 

Server”: TFTP (Trivial File Transfer Protocol), FTP, or HTTP.

For example, 8180 configuration files can be automatically downloaded 

from a TFTP server using DHCP Option 66. This option code (when set) 
supplies a TFTP boot server address to the DHCP client to boot from. 

DHCP must be enabled if using DHCP Option 66, in order for 

Provisioning to work (see “DHCP” on page 22).

One of two files can be uploaded on the Provisioning Server (for access 

via TFTP, FTP, or HTTP):

           generic file algop8180.conf or specific file algom[MAC].conf

 

Summary of Contents for 8180




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands