ALFAtron ALF-MUH88E User Manual Download Page 28 | Manualshive

Page: 28 / 44

background image

ALFATRON ALF-MUH88E

23

4.3 TCP/IP Control

Besides IR control, RS232 control, the Matrix Switcher boasts option TCP/IP port for IP
control.

Default settings: IP: 192.168.0.178; Subnet Mast: 255.255.255.0; Gateway:
192.168.0.1; Serial Port: 4001.

IP& gateway can be changed as you need, Serial Port cannot be changed.

Connect the Ethernet port of control device and TCP/IP port of the Matrix Switcher, and
set same network segment for the 2 devices, users are able to control the device via
web-based GUI or designed TCP/IP communication software.

Control Modes

The Matrix Switcher can be controlled by PC without Ethernet access or PC(s) within a
LAN.



Controlled by PC

Connect a computer to the TCP/IP port of the Matrix Switcher, and set its network
segment to the same as the Matrix Switcher’s.



Controlled by PC(s) in LAN

Connect the Matrix Switcher, a router and several PCs to setup a LAN (as shown in the

Same network
segment as
the switcher

«
...
26
27
28
29
30
...
»

Summary of Contents for ALF-MUH88E













































Reviews:

No comments

Related manuals for ALF-MUH88E

RackSwitch G8264

Brand: IBM Pages: 20

Flex System FC3171

Brand: IBM Pages: 64

Brand: H3C Pages: 32

Brand: H3C Pages: 22

Brand: H3C Pages: 488

Brand: H3C Pages: 3

Brand: H3C Pages: 8

Brand: H3C Pages: 25

Brand: H3C Pages: 31

Brand: H3C Pages: 23

Brand: H3C Pages: 24

Brand: H3C Pages: 126

Brand: H3C Pages: 42

Brand: H3C Pages: 32

Brand: H3C Pages: 13

Brand: H3C Pages: 16

Brand: H3C Pages: 39

Brand: DANLERS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands