manualshive.com logo in svg

Alfa Laval Toftejorg MultiJet 65, Instruction Manual

Share
Download
Alfa Laval Toftejorg MultiJet 65 Instruction Manual Download Page 19

5 Operation

MultiJet 65

5.2

Safety precautions

The machine is intended for use inside a tank only. As peak velocity of main jets reaches 40 m/sec., The Alfa Laval Toftejorg
MultiJet 65 must not be operated in open air or when tank is open.

Warning:

Hot chemicals and steam under pressure may be used for cleaning and sterilising. Protect against scalding
and burning. Never tamper with or try to open clamps or other connections while system is in operation.
Make sure that system is depressurised and drained before disassembly.

The cleaning jets impinging the tank surface are a source of noise. Depending on pressure and distance to the tank walls, noise
level may reach up to 85 dB.

Warning:

Tanks may contain poisonous/hazardous products or products which represent an environmental or
safety risk. Never open tank and dismount the machine without checking previous tank contents and
necessary precautions.

See also 3.6 ATEX/IECEx temperature class and code, page 9.

19

Summary of Contents for Toftejorg MultiJet 65

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands