Alfa Laval LKH Evap Instruction Manual Download Page 6

Page: 6 / 48

2 Safety

All warnings in the manual are summarised on this page.
Pay special attention to the instructions below so that severe personal injury and/or damage to the pump are avoided.

2.3 Safety precautions

IInnssttaallllaattiioonn::

Allw

waayyss read the technical data thoroughly. (See chapter 6 Technical data)

Allw

waayyss use a lifting crane when handling the pump.

Puum

mpp w

wiitthh IIm

mppeelllleerr ssccrreew

w::

Neevveerr start in the wrong direction of rotation with liquid in the pump.

Allw

waayyss have the pump electrically connected by authorised personnel. (See the motor instruction)

Oppeerraattiioonn::

Allw

waayyss read the technical data thoroughly. (See chapter 6 Technical data)

Neevveerr touch the pump or the pipelines when pumping hot liquids or when sterilising.

Neevveerr run the pump with both the suction side and the pressure side blocked.

Neevveerr run the pump when partially installed or not completely assembled.

Neecceessssaarryy precautions must be taken if leakage occurs as this can lead to hazardous situations.

Allw

waayyss handle lye and acid with great care.

Neevveerr use the pump for products not mentioned in Alfa Laval pump selection program.

Alfa Laval pump selection program can be acquired from your local Alfa Laval sales company.

Maaiinntteennaannccee::

Allw

waayyss read the technical data thoroughly. (See chapter 6 Technical data)

Neevveerr service the pump when it is hot.

Neevveerr service the pump if pressurized.

Moottoorrss w

wiitthh ggrreeaassee nniipppplleess::

Remember lubrication according to information plate/label on the motor.

Allw

waayyss disconnect the power supply when servicing the pump.

Allw

waayyss use Alfa Laval genuine spare parts.

TTrraannssppoorrttaattiioonn::

TTrraannssppoorrttaattiioonn ooff tthhee ppuum

mpp oorr tthhee ppuum

mpp uunniitt::

Neevveerr lift or elevate in any way other than described in this manual

Allw

waayyss drain the pump head and accessories of any liquid

Allw

waayyss ensure that no leakage of lubricants can occur

Allw

waayyss transport the pump in it’s upright position

Allw

waayyss ensure that the unit is securely fixed during transportation

Allw

waayyss use original packaging or similar during transportation

CONTACT CSI FOR MORE INFORMATION | CSIDESIGNS.COM | [email protected] | 417.831.1411

Summary of Contents for LKH Evap

















































Search results

Summary of Contents for LKH Evap

Reviews:

Related manuals for LKH Evap

Brands by name

Popular brands

Alfa Laval LKH Evap, Instruction Manual

Search results

Summary of Contents for LKH Evap

Reviews:

Related manuals for LKH Evap

Brands by name

Popular brands