User’s manual
Weather station with wireless outdoor sensor
WS-2200
Overview:
Indoor unit:
1. Display:
Shows time, indoor and outdoor temperature and
weather forecast.
2.
SNOOZE / LIGHT
button :
Snooze button for the alarm function.
Also turns on the display lighting.
3.
ALARM SET
button :
For checking and setting the wake-up alarm.
4.
CH/+
button:
Selection button when using multiple outdoor units
and the ‘+’ button during setup.
5.
MEM/-
button:
Memory button when checking min and max val-
ues and the ‘-’ button during setup.
6.
DISPLAY SET
button:
Function setup button.
7.
°C / °F
switch:
To switch the temperature display between
degrees Celsius and degrees Fahrenheit.
8.
SENSOR
button:
To pair the indoor unit with the outdoor unit.
9.
RCC
button:
To turn the DCF receiver on or off.
10.
RESET
button:
To restart the indoor unit in case of a (possible)
error.
11. Battery compartment.
Outdoor unit:
1. Monitor-LED:
Illuminates as soon as the outdoor unit is sending
measurement data to the indoor unit.
2.
CH 1.2.3
switch:
To set the outdoor unit to a different channel.
3.
RESET
button:
To restart the outdoor unit in case of a (possible)
error.
4. Suspension eye:
Provision to suspend the outdoor unit from a wall.
5. Battery compartment.
Power supply:
Indoor unit:
Slide down the battery cover at the rear of the unit
and insert 2 AA 1.5V batteries according to the mark-
ings inside the battery compartment. Slide the battery
cover back onto the indoor unit.
The indoor unit will now start a 1 minute scan to
search for the outdoor unit. Therefore, you’ll need to
insert the batteries into the outdoor unit within that
minute.
Outdoor unit:
Slide down the battery cover at the rear of the unit,
slide the CH switch to the position ‘1’ and insert 2 AA
1.5V batteries according to the markings inside the
battery compartment. Slide the battery cover back
onto the outdoor unit.
Weak battery warning:
As soon as the batteries of the outdoor unit become
exhausted, the
symbol will illuminate on the
display of the indoor unit.
Now please replace the batteries of the outdoor unit.
The indoor unit does not provide a battery warning.
Replace the batteries of this unit as soon as the
display becomes dim or weak.
Pairing the indoor unit / outdoor unit:
Automatically:
As soon as you insert the batteries into the indoor
unit, the indoor unit will start a 1 minute scan to
search for the signal of the outdoor unit. Therefore,
if you insert the batteries into the outdoor unit within
that minute and the units will ‘find’ each other, they
will be automatically paired and the display of the
indoor unit will show the temperature transmitted by
the outdoor unit.
Manually:
If the units cannot be paired automatically, or after
replacing the batteries, you can pair the outdoor unit
(again) with the indoor unit as follows:
1.
use a sharp object to briefly press the
RESET
button on the rear of the indoor unit
2.
use a sharp object to briefly press the
RESET
button on the rear of the outdoor unit
3.
the units will find each other (again) after several
seconds and the indoor unit will display the tem-
perature transmitted by the outdoor unit.
Clock:
Introduction
The WS-2200 is provided with a built-in DCF receiver
which receives the DCF time signal from Frankfurt.
This signal ensures that the clock shows the time
very accurately, provided a strong enough signal is
being received.
Automatically:
As soon as you insert the batteries into the indoor unit,
the clock will start searching for the DCF radio signal
for the time while the
antenna symbol is flashing.
After several seconds or minutes the WS-2200 will
start showing the correct time. In extreme cases, it can
take over a day before the DCF time is shown.
Manually:
If the clock cannot receive the radio signal or cannot
receive it well enough, you can set the clock manually
as follows:
1. press and hold the
DISPLAY SET
button for
2 seconds, 12Hr or 24Hr will appear in the display
2.
use +/- to set the time format, then briefly press
the
DISPLAY SET
button
3.
use +/- to set the hours and then briefly press the
DISPLAY SET
button
4.
use +/- to set the minutes and then briefly press
the
DISPLAY SET
button
5. use +/- to set the seconds to 0 (this allows you to
have the clock run synchronously with your own
clock) and then briefly press the
DISPLAY SET
button
6. use +/- to set the hour difference compared to the
DCF time. E.g. for use in the Benelux select ‘0’
and then briefly press the
DISPLAY SET
button
The clock is now set manually.
When the DCF receiver is enabled and a strong
signal is being received, the receiver will overwrite
the clock display.
Switching the DCF receiver on/off:
You can turn off the DCF receiver as follows, allowing
you to have only the time and date shown on the
display according to your programming:
• turn off: press and hold the
RCC
button at the
rear of the indoor unit for 4 seconds until the
antenna symbol disappears.
You can turn the receiver back on as follows:
•
turn on: briefly press the
RCC
button at the rear of
the indoor unit until the antenna symbol starts
flashing
‘DST’ in the display.
‘DST’ stands for Daylight Saving Time.
‘DST’ illuminates when the displayed time is the
daylight saving time.
1
2
3
4
1
2
3
6
5
4
7
8
9
10
11
433MHz
THERMO SENSOR
RESETCH 1 2 3
