background image

700W AIRLESS SPRAY STATION

29

700W AIRLESS SPRAY STATION

28

Does not draw in paint 

when the Prime/Spray 

knob is set to PRIME 

position

The airless spray station is not 

primed prroperly

Prime the airless spray station

The suction tube is not 

immersed in the paint

Immerse the suction tube in the 

paint

The suction tube is clogged

Clean the suction tube and 

suction tube filter

The suction tube is not 

connected to the suction tube 

inlet port properly

Check the connection and 

tighten the connection

The valve of the Prime/Spray 

knob is faulty

Repair by an authorised service 

centre

Draws up paint but the 

pressure drops when 

spraying

The spray tip is worn

Replace the spray tip with a new 

one

The suction tube filter is 

clogged

Clean the suction tube filter

The spray gun filter is clogged Clean the spray gun filter
The paint is too thick

Thin the paint according to the 

manufacturer's instructions

The Prime/Spray knob 

is in the SPRAY position, 

but the paint flows 

through the return tube

The Prime/Spray knob is dirty 

and worn

Repair by an authorised service 

centre

The spray gun leaks

The spray tip is not assembled 

properly

Check the spray tip assembly

A seal is dirty

Clean the seal

The spray gun will not 

spray

The spray tip or the spray gun 

filter is blocked

Clean the spray tip and the spray 

tube filter. Ensure the spray tube 

filter is seated properly

The spray tip is in the reverse 

position

Check and turn the spray tip in 

the forward position

The paint pattern is 

tailing

The Pressure Control Dial is set 

too low

Turn the Pressure Control Dial to 

a higher setting

The spray gun filter, spray tip 

or the suction tube filter is 

clogged

Clean the spray gun filter, spray 

tip or the suction tube filter

The connection of the suction 

tube is loose at the Suction 

Tube Inlet Port

Tighten the connection

The spray tip is worn

Replace the spray tip

The paint is too thick

Thin the paint according to the 

manufacturer's instructions

16. TECHNICAL SPECIFICATIONS

Model No.

PLD3090

Rated voltage

220-240V~ 50Hz

Rated wattage

700W

Maximum flow rate

1100ml/min

Maximium spray pressure

3000psi

Weight

8.7kg

Hose length

7.5m

Technical Specifications

Residual Risks

[email protected] 

01904 727506 

01247 5150 

GB 
IRE 

[email protected] 

01904 727506 

01247 5150 

GB 
IRE 

 

Noise information

 

WARNING!

Sound  pressure  

95.4 

  dB(A); uncertainty K = 3 dB(A) 

   

 

 

 

Health hazard!

Working without ear protection and suitable protective clothing poses a health 

hazard.

 

− Wear ear protection and suitable protective clothing when working with 

the device.

Measured in accordance with DIN EN 60745. The noise at your workplace may 

 exceed 85 dB(A); protective measures are necessary in this case (wear suitable ear 

protection).

  Sound pressure level :

95.4 dB(A)

  Uncertainty K:

3 dB(A)

The aforementioned values are noise emission values and therefore, do not 

necessarily represent safe values for the workplace. The correlation between 

emission and imission levels cannot reliably provide for a conclusion as to whether 

additional cautionary measures are necessary or not.
Factors that could affect the respective imission level present at the workplace involve 

the specification of the work area, the surrounding area, the duration of exposure, 

other noise sources etc. 

Summary of Contents for Workzone Titanium+ 85509



















Reviews: