24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: [email protected]
1800 909 909
MODEL: №. 2024001 • 02/2017 • 55945
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: [email protected]
1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №.2024001 • 02/2017 • 55945
24
25
Warranty/Service
Troubleshooting
Environmental protection
Recycle unwanted materials instead of disposing of them as waste.
All tools, hoses and packaging should be sorted, taken to the local
recycling centre and disposed of in an environmentally safe way.
What your 3 year warranty means
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly.
In the event of product failure within its intended use over the course of
the first 3 years after the date of purchase, we will remedy the problem as
quickly as possible once it has been brought to our attention. In the unlikely
event of such an occurrence, or if you require any information about the
product please contact us via our after sales support services, details of
which can be found in this manual and on the product itself.
After Sales Support TEL: 1800 909 909
Service Support
If you have any issues with the operation of your product, please call us on
1800 909 909 for advice, or email us at [email protected]
Accessories and After Sales Parts
The following accessories are available for purchase by visiting
www.extrabattery.com.au or calling our customer service hotline on:
1800 909 909
1. 2024001-BAT - 24V
1.5Ah Battery (55945)
2. 2024001-CBA - 24V
Charger Adaptor
(55945)
3. IVP 2600-0450WS
Plug Pack Charger
(55945
)
FAQ/Troubleshooting
Do I need to charge the battery before use?
Yes, New battery packs are shipped in a low charge condition and must be fully charged
before use. It takes approximately 3-5 hours to fully charge your new battery.
Follow the full section “Battery Charging “ in this manual on page 14-15.
Charging of batteries should not be undertaken casually. Through the charging cycle the
condition of the battery pack should be monitored and the charge cycle turned off at
completion or at the end of the recommended time.
How do I obtain the best life for the battery?
- Never allow the battery to run completely empty before recharging. The battery should be
placed on charge whenever the battery is noticeably running down or the drill no longer
performs a task it previously performed.
- Avoid allowing lose items like screws or nails etc. to be stored with battery packs as these
or similar items can short battery packs and cause a fire or explosion.
- Always unplug the charger when not in use and store in a dry secure place.
- Avoid charging or storing your battery in temperatures below 0ºC and above 45ºC.
How do I use the 2 gears on the drill?
To select the LOW gear (low speed, high torque setting), push the gear selector backward,
towards the back of the drill/driver. The number “1” will be displayed.
To select the HIGH gear (high speed, low torque setting), push the gear selector forward,
towards the chuck. The number “2” will be displayed.
NOTE: The gears cannot be changed if the variable speed / on off trigger (8) is depressed.
How do I adjust the torque?
The torque function will only operate when the screw function (14) is selected by rotating
the function selection collar (3) and aligning the screw symbol with the triangular indicator
on the top of the drill.
To adjust the torque setting you rotate the torque collar (2). The higher the number, the
higher the torque setting collar.
Controlling the torque allows for better control when using the drill/driver on specific add
screwing tasks and assists in preventing over-fastening and over-tightening.
For setting the torque position, first select a low setting on the torque collar (2) and align
the selected symbol with the triangular indicator on the top of the drill/driver.
Slowly increase the torque setting to the desired level. It is suggested to test the setting on
scrap material first.