manualshive.com logo in svg

Alcorn Mcbride AmpTraXX, User Manual

Share
Download
Alcorn Mcbride AmpTraXX User Manual Download Page 12

 

 

September 12, 2005  •   Alcorn McBride AmpTraXX  User’s Manual    •    Rev 1.2 

Page 8 

 

Firmware Update Mode 

While in Firmware Update 
Mode, AmpTraXX will not 
operate normally.  All 
filters and amplifiers will 
remain off until this switch 
is returned to the ON state. 

Whenever switch #3 is in the 

OFF

 (

Up

) position, AmpTraXX will be in Firmware 

Update Mode.  In this mode of operation, AmpTraXX will sit in an idle state and 
wait for a firmware update via RS-232.  For a detailed explanation on Updating 
AmpTraXX firmware, see the 

Updating Your Firmware

 section.   

 

 

Ground Lift 

 

In the event of AC hum or noise, the fourth key on the 4 key DIP switch, may be 
opened to isolate the unit’s ground from its chassis.  For ground lifting, push the DIP 
switch #4 to the 

OFF

 (

Up

) position. 

 

 

 

Unbalanced Inputs 

For balanced input obtain 
the optional balanced 
audio input module. 

Sixteen RCA jacks are used for unbalanced audio input.   

 

 

Summary of Contents for AmpTraXX
































Reviews:

No comments

Brands by name

Popular brands

Load more brands